Telephone Button Programming
500 Series Programs
13-86 Strata CTX Programming - Part 3:Telephone Button Programming 04/03
570
Account Code Digit
Length
,
+ROG
Accounting Codes need to be specified for the number of digits that
are expected to be used for registering a number. This allows dialing
within Strata CTX to proceed automatically once the correct account
code is dialed. The following numbers are then dialed digits used for
making the phone call.
A second length is provided to allow the number of digits to be used
for verification of the code to be less than the total code entered; thus,
the code may contain two parts, one required and one part optional to
the user..
570-01 Verified Digit Length
)%
, n,
+ROG
n = 4~15
(default = 4)
The Verified Digit Length sets a number of digits to verify with a pre-
set list. This number may be the same or smaller than the account
code digits set to be entered for creating a complete accounting code.
Note This field is not changed, when “Program 506” on page
13-73 are registered.
570-02 Registered Digit
Length
)%
, n,
+ROG
,
+ROG
n = 4~15
(default = 6)
The Registered Digit Length sets a number for the digits to be entered
to make a complete accounting code entry.
Note The Registered Digit Length (
)%
) must be greater than or
equal to the Verified Digit Length (
)%
).
571
Exception Numbers
for Forced Account
Codes
,
+ROG
Up to four telephone numbers can be programmed as exceptions to
the forced and /or verified account code entries (including 911).
These special codes enable numbers to bypass the verification
process and proceed unhindered.
571-01 Exception Number 1
)%
, n,
+ROG
n = Up to 4 digits
Exception 1 default = 911
Exception 2~4 default = no
value
Enter a Forced Account Code Exception.
Note One of the assigned exception numbers should be 911.
Exception Numbers for Forced Account Code fields cannot
be duplicated.
571-02 Exception Number 2
)%
, n,
+ROG
571-03 Exception Number 3
)%
, n,
+ROG
571-04 Exception Number 4
)%
, n,
+ROG
,
+ROG
573
Delete Door Phone
,
+ROG
This command deletes door phone.
573-00 Door Phone
n,
+ROG
,
+ROG
n = 1~6 (CTX100)
1~9 (CTX670 Basic)
1~24 (CTX670 Exp.)
Enter the number of the door phone that is to deleted.
576
Door Phone Night
Ring Over External
Page
,
+ROG
This command assigns a Page Group to ring during system Night
Mode when a door phone button is pressed. The assignment can be
made independently for each Tenant.
576-00 Tenant Number
n,
+ROG
n = 1~2 (CTX100)
1~8 (CTX670)
Select the system Tenant number to be assigned Door Phone to Page
Group/Night Ringing.
576-01 Page Group Number
)%
, n,
+ROG
,
+ROG
n = 0~4 (CTX100)
0~8 (CTX670 Basic)
0~16 (CTX670 Exp.)
(default = 0)
Select the system Page Group number that should ring for the
selected Tenant when a door phone button is pressed during the
system Night Mode.
577
Caller History
,
+ROG
This command assigns which station stores Caller ID information for
PDN,CO,GCO and POOL line buttons
577-00 Circuit Type/Number
n,
+ROG
n = Up to 6 digits Enter the Circuit Type and number. See the Table on page 13-87
below.
577-01 Primary DN
)%
, n,
+ROG
,
+ROG
n = Up to 5 digits Enter Station DN to store call history data.
Programs 500~577 (continued)
Button Sequence Value(s) Summary
To Next Page
Loading...
