YASKAWA Z1000 - Page 389

Drive/kVA Selection ........................................................... 322
Drive Capacity Setting Fault .................................................. 227
Drive Cover......................................................32, 33, 34, 35, 36
Drive Derating Data ............................................................ 278
Drive Disabled .................................................................. 221
Drive Mode ................................................................ 112, 115
Drive Model Mismatch ........................................................ 233
Drive Models and Types.........................................................49
Drive Model Selection ......................................................... 190
Drive Mode Unit Monitor Selection ......................................... 187
Drive Nameplate ..................................................................27
Drive Operations by BACnet ................................................. 350
Drive Operation Status at Previous Fault.................................... 334
Drive Overheat Warning....................................................... 224
Drive Overload.................................................................. 215
Drive Ready ..................................................................... 103
Drive Slave Address...................................................... 178, 346
Drive Specifications ............................................................ 274
Drive Status...................................................................... 333
Drive Transmit Wait Time .............................................. 179, 347
Drive Unit Signal Fault ........................................................ 209
Drive Watt Loss Data .......................................................... 276
Dynamic Audible Noise Control Function Selection ...................... 324
E
E1-08 ............................................................................. 200
E1-10 ............................................................................. 200
EEPROM Memory Data Error................................................ 208
EEPROM Write Error.......................................................... 210
EF ................................................................................. 221
EF0 ......................................................................... 209, 221
EF1 ......................................................................... 209, 222
EF2 ......................................................................... 209, 222
EF3 ......................................................................... 209, 222
EF4 ......................................................................... 209, 222
EF5 ......................................................................... 209, 222
EF6 ......................................................................... 209, 222
EF7 ......................................................................... 209, 222
EMC Filter and Drive Installation for CE Compliance.............. 369, 370
EMC Filter Installation......................................................... 367
EMC Filters...................................................................... 367
EMC filter switch SW1 ..........................................................37
EMC filter switch SW2 ..........................................................37
EMC Guidelines ................................................................ 366
EMC Guidelines Compliance ................................................. 367
Emergency Override Reference Selection................................... 329
Emergency Override Speed ................................................... 329
Enclosure Types ..................................................................29
End................................................................................ 233
End3 .............................................................................. 231
End4 .............................................................................. 231
End5 .............................................................................. 231
End7 .............................................................................. 231
Energy Saving Constants Error ............................................... 229
Enter Command................................................................. 180
Enter command necessary ............................................... 180, 348
Enter command not necessary .......................................... 181, 348
Enter Command Types......................................................... 358
Enter Data from the Motor Nameplate....................................... 146
ENTER Key ..................................................................... 107
Er-01
.............................................................................. 231
Er-02.............................................................................. 232
Er-03.............................................................................. 232
Er-04.............................................................................. 232
Er-05.............................................................................. 232
Er-08.............................................................................. 232
Er-09.............................................................................. 232
Er-12.............................................................................. 232
Err................................................................................. 210
Error Reading Data ............................................................. 234
Errors and Displays When Using the Copy Function...................... 206
Error Writing Data.............................................................. 233
European Standards ............................................................ 366
Excessive Motor Oscillation and Erratic Rotation ......................... 241
Excessive PI Feedback................................................... 210, 222
Exterior and Mounting Dimensions ............................................49
External Fault ............................................................. 209, 222
External Interlock............................................................... 103
F
F1/F2 Key Function Selection ................................................ 190
FAn ............................................................................... 210
Fan Application ................................................................. 124
Fan Bracket .......................................................... 32, 33, 34, 35
Fan Cover ..........................................................................30
Fan Finger Guard .................................................................30
Fan Guard........................................................32, 33, 34, 35, 36
Fan with PI Control Application.............................................. 125
Fault Causes and Solutions .................................................... 207
Fault Detection .................................................................. 207
Fault Displays ................................................................... 207
Fault History..................................................................... 194
Fault Relay Output................................................................92
Fault Reset Interval Time................................................ 181, 315
Fault Reset Methods............................................................ 236
Fault Reset Operation Selection ........................................ 181, 316
Faults ....................................................................... 203, 204
Fault Trace................................................................. 194, 235
FbH ......................................................................... 210, 222
FbL ......................................................................... 211, 222
FE ...................................................................................91
Ferrule Dimensions...............................................................94
Ferrule Terminal Types and Sizes ..............................................94
Ferrule-Type Wire Terminals ...................................................94
Fine-Tuning Open Loop Vector Control for PM Motors.................. 201
Fine-Tuning V/f Control....................................................... 200
FM ..................................................................................92
Fn1................................................................................ 210
Forward/Reverse Run Command Input Error............................... 221
Frequency Accuracy (Temperature Fluctuation) ........................... 274
Frequency Control Range...................................................... 274
Frequency Reduction Rate during Overheat Pre-Alarm............. 185, 317
Frequency Reference ..................................................... 171, 332
Frequency Reference at Previous Fault ...................................... 334
Frequency Reference at Reference Loss............................... 139, 315
Frequency Reference from MEMOBUS/Modbus Comm. ................ 337
Frequency Reference Inputs.....................................................91
Frequency Reference Loss Detection Selection ...................... 138, 315
Frequency Reference Lower Limit ........................................... 133
Frequency Reference Monitor Content During PI ......................... 168
Index
YASKAWA ELECTRIC TOEP C710616 45F YASKAWA AC Drive – Z1000 User Manual
389