Alcatel-Lucent OmniSwitch 6860 Series - Page 1076

Index
OmniSwitch AOS Release 8 Network Configuration Guide December 2017 Index-8
modifying 24-18
password 24-19
probe expect 24-20
probe send 24-20
retries 24-19
servers 24-18
TCP/UDP port 24-19
timeout 24-18
URL 24-19
user name 24-19
service l2profile command 28-49
severity level
see switch logging
show arp command 15-14
show arp filter command 15-16, 15-31
show health command 34-39
show health interval command 34-38
show health threshold command 34-8, 34-37
show icmp control command 15-34
show icmp statistics command 15-34
show ip config command 15-20, 15-26
show ip interface command 15-8
show ip redist command 19-16
show ip rip command 19-7
show ip rip interface command 19-7
show ip route command 15-12, 17-18
show ip route-map command 19-13
show ipv6 interface command 17-13
show linkagg command 8-11
show linkagg port command 8-11
show lldp remote-system command 13-3
show lldp statistics command 13-3
show log swlog command 36-7
show mac-address-table port-mac command 5-16
show policy rule command 24-12
show policy server long command 27-6
show port mirroring status command 34-16
show port monitoring file command 34-22
show port-security command 33-3
show port-security shutdown command 33-3
show qos log command 26-40
show rmon events command 34-31
show rmon probes command 34-7, 34-31
show tcp ports command 15-36
show tcp statistics command 15-36
show udld configuration command 2-3
show udld statistics port command 2-3
show udp ports command 15-36
show udp statistics command 15-36
show vlan svlan command 12-13, 35-26
show vlan svlan port-binding command 12-13
show vlan svlan port-config command 12-13, 35-26
SLB
see Server Load Balancing
SNMP
attributes for LDAP authentication servers 31-22
source learning 3-1
defaults 3-2
MAC address table 3-1, 3-3
source learning time limit 33-12
Spanning Tree Algorithm and Protocol 6-1, 11-1
1x1 operating mode 4-9, 6-20, 6-22
application examples 6-10, 6-43
bridge ID 6-7, 6-28
Bridge Protocol Data Units 6-7, 6-29, 6-30
bridged ports 6-33
designated bridge 6-5
flat operating mode 4-9, 6-20, 6-21
path cost 6-36, 6-37
port connection types 6-40
Port ID 6-7
port ID 6-35
port path cost 6-5
port roles 6-5
port states 6-6, 6-38
root bridge 6-5, 6-29, 6-30
root path cost 6-5
topology 6-5, 6-11
Topology Change Notification 6-8
Spanning Tree Bridge
defaults 6-3, 11-2
Spanning Tree bridge parameters
802.1D standard protocol 6-27
802.1s multiple spanning tree protocol 6-27
802.1w rapid reconfiguration protocol 6-27
automatic VLAN containment 6-31
forward delay time 6-30
hello time 6-29
maximum age time 6-29
priority 6-28
Spanning Tree Port
defaults 6-3
Spanning Tree port parameters 6-33
connection type 6-40
link aggregate ports 6-35, 6-36, 6-38, 6-39, 6-41
mode 6-38
path cost 6-36
priority 6-35
SSL
for LDAP authentication servers 31-26
policy servers 27-6
static agg agg num command 8-3, 8-7
static link aggregation 8-1
adding ports 8-7
application examples 8-3, 8-10
configuration steps 8-6
creating 8-7
defaults 8-2
deleting 8-7
deleting ports 8-8
disabling 8-9
enabling 8-9
group names 8-9
groups 8-5, 9-5
overview 8-5, 9-5
verify information about 8-11
static linkagg admin state command 8-9
static linkagg name command 8-9