Version 7.2 1087 Mediant 1000B Gateway & E-SBC
User's Manual 65. Configuration Parameters Reference
Parameter Description
Media IP Version
Preference
media-ip-ver-pref
[MediaIPVersionPreference]
Global parameter that defines the preferred RTP media IP addressing
version (IPv4 or IPv6) for outgoing SIP calls. You can also configure
this functionality per specific calls, using IP Profiles
(IpProfile_MediaIPVersionPreference). For a detailed description of
the parameter and for configuring this functionality in the IP Profiles
table, see Configuring IP Profiles on page 423.
SIT Q850 Cause
configure voip > sip-
definition settings > sit-
q850-cause
[SITQ850Cause]
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when a Special Information Tone
(SIT) is detected on an IP-to-Tel call.
The valid range is 0 to 127. The default is 34.
Note: For mapping specific SIT tones, you can use the
SITQ850CauseForNC, SITQ850CauseForIC, SITQ850CauseForVC,
and SITQ850CauseForRO parameters.
SIT Q850 Cause For NC
configure voip > sip-
definition settings > release-
cause-for-sit-nc
[SITQ850CauseForNC]
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when SIT-NC (No Circuit Found
Special Information Tone) is detected from the Tel side for IP-to-Tel
calls.
The valid range is 0 to 127. The default is 34.
Note: When not configured (i.e., default), the SITQ850Cause
parameter is used.
SIT Q850 Cause For IC
configure voip > sip-
definition settings > q850-
cause-for-sit-ic
[SITQ850CauseForIC]
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when SIT-IC (Operator Intercept
Special Information Tone) is detected from the Tel for IP-to-Tel calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note: When not configured (i.e., default), the SITQ850Cause
parameter is used.
SIT Q850 Cause For VC
configure voip > sip-
definition settings > q850-
cause-for-sit-vc
[SITQ850CauseForVC]
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when SIT-VC (Vacant Circuit - non-
registered number Special Information Tone) is detected from the Tel
for IP-to-Tel calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note: When not configured (i.e., default), the SITQ850Cause
parameter is used.
SIT Q850 Cause For RO
configure voip > sip-
definition settings > q850-
cause-for-sit-ro
[SITQ850CauseForRO]
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when SIT-RO (Reorder - System
Busy Special Information Tone) is detected from the Tel for IP-to-Tel
calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note: When not configured (i.e., default), the SITQ850Cause
parameter is used.
configure voip > gateway
manipulation settings >
inbound-map-set
[GWInboundManipulationSe
t]
Selects the Manipulation Set ID for manipulating all inbound INVITE
messages. The Manipulation Set is defined using the
MessageManipulations parameter. By default, no manipulation is
done (i.e. Manipulation Set ID is set to -1).
Note: The parameter is applicable only to the Gateway application.
configure voip > gateway
manipulation settings >
Selects the Manipulation Set ID for manipulating all outbound INVITE
messages. The Manipulation Set is defined using the
MessageManipulations parameter. By default, no manipulation is
To Next Page
Loading...
