000 299 119 5 - BA ROLLANT 240 - 250 - 254 - 255 16.1.1
Index
INDEX
A
Accessing the setup menu .........................................11.2.1
Activate manual net wrapping
.......................................9.1.9
Adjusting the baling pressure with a pivoting segment
......8.1.10
Adjusting the chain tightener
......................................14.3.4
Adjusting the drawbar fork arms
....................................7.2.9
Adjusting the flow rate
..............................................14.4.4
Adjusting the height of the cutting knives
(ROLLANT 250/254/255 RC)
.....................................14.5.1
Adjusting the hitch eye
.................................... 7.2.5, 7.2.10
Adjusting the length of the drawbar fork arms
...................7.2.4
Adjusting the pressure springs for the pressure roller
.......14.3.7
Adjusting the roller crop guard
......................................8.1.4
Adjusting the roller crop guard where there are problems
with the bale material feed.
..........................................8.1.5
Adjusting the spring-loaded cylinder for the front
bale-forming roller drive
............................................14.3.5
Adjusting the tension of the drive chains
.......................14.3.3
Adjusting the tension spring for the net brake
.................14.3.7
Adjusting the tension spring for the net roll tightening
clamp (Adjustment done without net roll)
.......................14.3.6
Adjusting the tightening device for the net knife
..............14.3.7
Adjusting the twine knife control
..................................14.3.8
Adjusting the twine tightener
......................................14.3.8
Adjusting the twine wrap on the outer edges of the bale
...8.2.13
Adjusting the volume of the audible warning signal
..........9.2.12
Adjusting the working height of the pick-up
(pick-up with gauge wheels)
.........................................8.1.1
Adjusting the working height of the pick-up
(pick-up without gauge wheels)
.....................................8.1.1
Adjustment of tension springs
.....................................14.3.6
Angle drive gearbox
.................................................14.3.2
Application example
.................................................10.6.1
Application menu
.....................................................11.1.6
Attach the baler
.........................................................7.2.1
Attaching the universal drive shaft to the tractor
..............7.2.11
Attaching to the jaw-type hitch with a counter nut
..............7.2.9
Attaching to the jaw-type hitch with a safety nut
................7.2.8
Attaching to the swinging drawbar with a counter nut
.........7.2.4
Attaching to the swinging drawbar with a safety nut
...........7.2.3
Automatic central lubrication of the bearing
(Rollant 254/255 - Option)
.........................................14.4.4
Automatic chain lubrication
........................................14.4.1
Automatic net wrapping
............................................11.6.7
Automatic opening of tailgate
.....................................11.6.9
Automatic twine and net wrapping
.................................9.1.2
Automatic wrapping
...................................................9.2.7
Aux. menu
.............................................................11.5.8
B
Baffle plate ...............................................................6.1.1
Bale chamber
...........................................................6.1.2
Bale chute
...........................................................11.6.10
Bale counter
................................................... 9.1.5, 9.2.8
Bale discharge ramp
........................................ 6.1.3, 7.6.1
Bale output
............................................................11.6.9
Bale transport
...........................................................6.1.3
Bale wrapper
..........................................................10.3.6
Balers with standard Controls (ROLLANT 240/250)
...........9.1.1
Bearings to be greased and main lubrication
installation (optional) (for ROLLANT 254/255)
................14.4.3
Before transporting the baler
........................................7.5.1
Before you hitch the baler
............................................7.2.2
Binding and ejecting bales
...........................................9.2.7
Blanking knives
.........................................................8.1.7
Bleed valve combination with pressure limiting valve
.......14.6.2
Blockage in the roller crop guard
...................................8.1.6
Blockages
................................................................9.2.1
C
Call up “User settings” submenu .................................10.3.2
Cam-type cut-out clutch – universal drive shaft
(optional equipment)
...................................................9.2.1
Castor gauge wheels (ROLLANT 250/254/255)
..............13.1.4
Check and observe before starting operation
...................7.1.1
Check tight fit of wheel nuts
.......................................14.8.1
Checking the delay time
..............................................9.1.7
Checking the position of the cutting unit
........................11.6.3
Claas Communicator
..................................................7.3.1
Claas Communicator (ROLLANT 254/255 optional)
.........13.1.3
Clean knives
...........................................................10.3.5
Clean the rollers (Rollant 254/255)
...............................14.7.1
Connecting the universal drive shaft to the baler
...............7.2.1
Connecting the universal drive shaft to the tractor
.............7.2.6
Control box
.................................................. 7.3.1, 13.1.2
Control panel (ROLLANT 254/255 optional)
...................13.1.2
Control Terminal
........................................................7.3.1
Control terminal - overview
........................................10.1.2
Correct bale count
...................................................10.4.4
Counter
.................................................................10.4.1
Counter menu
.........................................................11.1.8
Crop guard
...............................................................6.1.1
Cutting device (ROTO CUT)
.......................................9.2.11
Cutting unit
..........................................8.1.7, 9.2.4, 14.5.1
Cutting unit (ROLLANT 250/254/255 RC)
........................6.1.1
Cutting unit active
....................................................11.6.3
Cutting unit deactivated
.............................................11.6.3
D
Daily and overall counter ...........................................10.4.1
Delay between bale end and beginning of net wrapping
...11.2.3
Delay time for automatic net wrapping
............................9.1.7
Delay wrapping cycle
................................................10.1.4
Delaying the wrapping process
...................................9.2.10
Delete fault
.............................................................10.5.2
Dimensions of the round baler
......................................5.1.4
Discharging bales
......................................................9.1.4
Discharging bales without the bale discharge unit
...........8.2.15
Disengaging the drive of the net wrapping mechanism
.....8.2.14
Disengaging the knives
...............................................9.2.4
Disengaging the twine wrapping drive
............................8.2.8
Display window current job
........................................11.1.8
Double twine wrapping
..............................................8.2.10
Drive system
..........................................................14.3.1
Index
To Next Page
Loading...
Need help?
General
