To Next PageTo Next PageWhat to do if Icom ID-31A Transceiver received call sign will not set to the operating call sign?
If the received call sign will not set to the operating call sign, the call sign has not been correctly received. Try it again, after the transceiver has again received its call sign.
What to do if the frequency cannot be set on Icom ID-31A?
If the frequency cannot be set on your Icom Transceiver, the Key Lock function may be activated. Hold down [LOCK] for 1 second to cancel it. Alternatively, the memory mode, Call channel mode, or DR mode may be selected; push [V/MHz] to select the VFO mode.
How to fix contacting problems with another station on Icom ID-31A?
If contacting another station is impossible on the Icom Transceiver, a different tone or code may be used for the tone/DTCS squelch. Check the tone/DTCS by performing a tone scan.
What to do if Icom ID-31A repeater does not transmit a reply after my call?
If the repeater does not transmit a reply after your call, it could be due to a wrong repeater setting. Ensure you set the correct repeater. Alternatively, the transceiver might be out of the repeater range, or your transmission isn't reaching the repeater. In this case, correct the repeater frequency, frequency offset, or duplex setting. You might also try accessing another repeater.
What to do if Icom Transceiver repeater replies ‘RX’ or ‘RPT?’ and the call sign of its gateway repeater after your call?
If the repeater replies with ‘RX’ or ‘RPT?’ and the call sign of its gateway repeater after your call, it may be because your MY call sign has not been set. In this case, set the MY call sign. Also, your own call sign might not be registered to the D-STAR Server, or it could be incorrect. Register your own call sign to the D-STAR Server, or confirm the registration of your own call sign. Finally, your calling station call sign might not be registered to the D-STAR Server, or it could be wrong. You should ask the server’s administrator about your calling station’s call sign.
What to do if the Icom Transceiver simplex operation cannot be made in the DR mode?
If simplex operation cannot be made in the DR mode, it might be because a call sign is programmed in the “CALL SIGN” of the Repeater list. Delete the Call sign in the “CALL SIGN” setting of the Repeater list. Another possible cause is that Duplex mode (DUP+, DUP–) is set. Select “OFF” in the “DUP” setting of the repeater list. Finally, a repeater frequency might be programmed. Program a simplex frequency instead.
Why won't a program scan start on my Icom ID-31A Transceiver?
If a program scan does not start on your Icom Transceiver: * The memory mode, Call channel mode, or DR mode may be selected. Push [V/MHz] to select the VFO mode. * The same frequency may have been programmed in the scan edge channels, “?A” and “?B.” Program different frequencies in the scan edge channels.
Why is there no sound coming from my Icom Transceiver speaker?
If no sound comes from the Icom Transceiver speaker, the volume level may be too low, so rotate [VOL] to adjust it. Also, check if an external speaker or cloning cable is connected to the [SP] jack and, if so, check the connection or remove the cable.
What to do if Icom Transceiver repeater replies ‘UR?’ and its call sign after your call?
If the repeater replies ‘UR?’ and its call sign after your call, wait for a while, and try it again.
How to make DR mode appear on Icom Transceiver?
If the DR mode does not appear even when holding down the button, the repeater list may have been cleared. Reprogram the repeater list using the CS-31 cloning software or reprogram the repeater list with the transceiver.
General| Display | LCD |
|---|---|
| GPS | Yes |
| D-STAR | Yes |
| Operating Temperature Range | -10°C to +60°C |
| Antenna Impedance | 50 Ohms |
| Type | Handheld |
| Frequency Range | 144-148 MHz / 430-450 MHz |
| Modulation | FM, D-STAR |
| Voltage | 7.4 V |
