EasyManua.ls Logo

Lenze L-force 9400 Series - Page 205

Lenze L-force 9400 Series
360 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
EDS94ARNExxxx EN 2.3 - 06/2014 L 205
9400 regenerative power supply module | Parameter setting
Diagnostics & fault analysis
Error messages
0x00770008 7798792 CPU: Temperature > C00126 No response C00589
0x0077000e 7798798 CPU: Thermal detector is defect Fault C00588
0x0091000f 9502735 Cyclic task: Standstill > 60 s Information -
0x007b000e
8060942 DC bus overvoltage Trouble C00600
0x007b000f 8060943 DC bus undervoltage Trouble -
0x0077000d
7798797 DC-bus capacitor: Thermal detector is defect Fault C00588
0x00750001 7667713 Device enabled Information -
0x00780001
7864321 Device utilisation Ixt > 100 % Fault -
0x00780000
7864320 Device utilisation Ixt > C00123 Warning C00604
0x00750005 7667717 Device: Pulse inhibit is active Information -
0x006a0011
6946833 Division by zero Fault -
0x0078000a
7864330 Electronic nameplate: Data are incompatible Information -
0x007b0030
8060976 Electronic nameplate: Data loaded Information -
0x007b0039
8060985 Electronic nameplate: Data outside parameter limits Information -
0x007b0032
8060978 Electronic nameplate: Encoder protocol unknown Information -
0x007b0033
8060979 Electronic nameplate: Encoder signal unknown Information -
0x007b0031
8060977 Electronic nameplate: Not found Information -
0x00910011
9502737 Error during initialisation System fault -
0x006a0002
6946818 Error during the update of inputs and outputs Fault -
0x006a0017
6946839 Error in control configuration System fault -
0x00750000
7667712 External error Fault C00581
0x007b002d 8060973 Failure of mains phase L1 Fault or
trouble in the case of failure
<500ms
-
0x007b002e 8060974 Failure of mains phase L2 Fault or
trouble in the case of failure
<500ms
-
0x007b002f
8060975 Failure of mains phase L3 Fault or
trouble in the case of failure
<500ms
-
0x006a0010
6946832 Faulty application parameter Fault -
0x006a0001
6946817 Faulty program download Fault -
0x007b001b
8060955 Feedback: Open circuit at X9 Fault -
0x008c0002
9175042 File DeviceCFG.dat is defect Fault -
0x008c0008
9175048 File DeviceCFG.dat is invalid Fault -
0x008c0005
9175045 File DeviceCFG.dat is missing Fault -
0x008c0001
9175041 File ProjectList.dat is defect Fault -
0x008c0007
9175047 File ProjectList.dat is invalid Fault -
0x008c0004
9175044 File ProjectList.dat is missing Fault -
0x008c0000
9175040 File ProjectSelection.dat is defect Fault -
0x008c0006
9175046 File ProjectSelection.dat is invalid Fault -
0x008c0003
9175043 File ProjectSelection.dat is missing Fault -
0x00770003
7798787 Filter: Overtemperature Fault C00583
0x00770002 7798786 Filter: Temperature > C00121 Warning C00584
0x0077000c 7798796 Filter: Thermal detector or FAN is defect Fault C00594
0x0068001a 6815770 Firmware has been changed Information -
0x0068001e
6815774 Firmware incompatible to control card System fault -
0x006a0000
6946816 General error in the application Fault -
0x00910003
9502723 Heartbeat not periodic System fault -
0x00770010
7798800 Heatsink: Fan is defect Fault C00610
0x00770001 7798785 Heatsink: Overtemperature Fault -
0x00770000
7798784 Heatsink: Temperature > C00122 Warning C00582
0x0077000a 7798794 Heatsink: Thermal detector is defect Fault C00588
Error number Error message Response Adjustable in
hex dec (Lenze setting)

Table of Contents

Other manuals for Lenze L-force 9400 Series

Related product manuals