7210 SAS-MXP, R6, R12, S, SX, T BASIC SYSTEM
CONFIGURATION GUIDE RELEASE 22.9.R1
Boot options
• Configuration notes for 7210 SAS-Sx 1/10GE, 7210 SAS-S 1/10GE, 7210 SAS-Sx 10/100GE, and
7210 SAS-Mxp
4.1.5.3 System boot options for 7210 SAS-Mxp, 7210 SAS-Sx 1/10GE, 7210 SAS-S 1/10GE,
and 7210 SAS-Sx 10/100GE in satellite mode
These platforms support the use of the external SD card slot or external compact flash (cf2:\) to boot
the system. Use the storage media supplied with the purchase of a valid satellite mode license. After you
insert the storage media in the external storage media slot, ensure that the satellite is connected to the
host before you power on the system.
Table 20: Uplink ports used for 7210 SAS platforms and variants in satellite mode lists the uplink ports
used for 7210 SAS platforms and their variants. To boot up in satellite mode, the uplinks must be
connected to the host ports, as described in Table 20: Uplink ports used for 7210 SAS platforms and
variants in satellite mode.
Note:
The following notes apply to the host port information listed in Table 20: Uplink ports used for
7210 SAS platforms and variants in satellite mode:
• In satellite mode, you cannot configure the BOF parameters uplinkA and uplinkB ports for use
with auto-init. For successful boot up in satellite mode, only use ports specified in Table 20:
Uplink ports used for 7210 SAS platforms and variants in satellite mode as uplinks to the 7750
SR host; use of other uplink ports is not supported. See Configuration notes for 7210 SAS-Sx
1/10GE, 7210 SAS-S 1/10GE, 7210 SAS-Sx 10/100GE, and 7210 SAS-Mxp for information
about ports used for first-time boot up with the chassis-role set to factory-default.
• On the 7210 SAS-Sx 10/100GE operating in satellite mode, you can establish a connection to
the host with one 100 GE or 10 GE uplink. However, Nokia recommends that you use more
than one uplink based on capacity requirements and to provide redundancy.
• On the 7210 SAS-Sx 10/100GE, by default, the DHCP requests are sent through ports 1/1/65
and 1/1/66, followed by 10GE ports 1/1/1 and 1/1/2. However, to use ports 1/1/1 and 1/1/2 as
uplink ports in satellite mode, you must first appropriately configure the ports in the 7750 SR
host machine.
• See the 7210 SAS Software Release Notes 22.x.Rx, part number 3HE 18217 000x TQZZA,
for information about the 7750 SR platforms and releases that support Ethernet satellites, and
the version of 7210 SAS satellite mode software that is compatible with a specific version of
SR OS software.
• On the 7750 SR, the 7210 SAS-Sx 10/100GE 100GE uplink ports are referred to as u1, u2,
u3, and u4:
– u1 - 1/1/65 and 1/1/c65 on the 7210 SAS-Sx 10/100GE 64SFP+ 4CFP4 and 7210 SAS-Sx
10/100GE 64SFP+ 4QSFP28 variants, respectively
– u2 - 1/1/66 and 1/1/c66 on the 7210 SAS-Sx 10/100GE 64SFP+ 4CFP4 and 7210 SAS-Sx
10/100GE 64SFP+ 4QSFP28 variants, respectively
– u3 - 1/1/67 and 1/1/c67 on the 7210 SAS-Sx 10/100GE 64SFP+ 4CFP4 and 7210 SAS-Sx
10/100GE 64SFP+ 4QSFP28 variants, respectively
3HE 18197 AAAB TQZZA
© 2022 Nokia.
Use subject to Terms available at: www.nokia.com/terms/.
130
SPACER TEXT
To Next Page
Loading...