Nokia 7210 SAS-Mxp - Procedure to Connect to a Console; Location of Console Ports on 7210 SAS Platforms

7210 SAS-MXP, R6, R12, S, SX, T BASIC SYSTEM
CONFIGURATION GUIDE RELEASE 22.9.R1
Boot options
• The 7210 SAS-Sx 1/10GE 46F 2C 4SFP+ and 7210 SAS-Sx 1/10GE 22F 2C 4SFP+ allow for 48 SFP
ports and 24 SFP ports respectively, along with an option to use copper interfaces on two ports.
• The 7210 SAS-Sx 1/10GE 48T 4SFP+ and 7210 SAS-Sx 1/10GE 24T 4SFP+ allow for 48
10/100/1000Mbps copper ports and 24 10/100/1000Mbps copper ports respectively.
• The 7210 SAS-Sx 1/10GE 48Tp 4SFP+ PoE and 7210 SAS-Sx 1/10GE 24Tp 4SFP+ POE allow for 48
10/100/1000Mbps copper ports and 24 10/100/1000Mbps copper ports respectively, along with option to
use PoE/PoE+, with a maximum of 720W of power being available to PoE devices across all the ports.
In addition, all variants support 4 x 10GE SFP+ ports that can be used as uplinks.
The following variants support the use of a 1GE fiber-optic SFP in a 10GE SFP+ port:
• 7210 SAS-Sx 1/10GE 48T 4SFP+
• 7210 SAS-Sx 1/10GE 24T 4SFP+
• 7210 SAS-Sx 1/10GE 48Tp 4SFP+ PoE
• 7210 SAS-Sx 1/10GE 24Tp 4SFP+ PoE
With this functionality, operators can use either 1GE or 10GE fiber uplinks. This enhancement provides
the flexibility of using SFP+ ports as 1GE uplinks with the capability to move to 10GE uplinks as bandwidth
demands grow. This functionality is supported for standalone mode only.
For a list of SFPs supported for 1GE operation, contact your Nokia representative.
Note:
• Before using a 1GE SFP in an SFP+ port, the SFP+ port speed must be set to 1000 Mb/s
with the config>port>ethernet>speed command; otherwise, an error message is generated
indicating that the SFP is unsupported. For information about setting the port speed, see
the "Ethernet Port Commands" section of the 7210 SAS-Mxp, R6, R12, S, Sx, T Interface
Configuration Guide.
• SFP+ ports that support SFPs do not support speeds of 10 Mb/s or 100 Mb/s.
The 7210 SAS-Sx 1/10GE can be operated in two modes – Standalone mode and Satellite mode:
• In satellite mode, the platform is managed by the 7x50 host. It does not need to be assigned an IP
address. The user needs to connect the right ports to the 7x50 and power on the node. The node
automatically fetches the BOF, the image and the configuration required to operate in satellite mode.
• In standalone mode, the platform provides IP/MPLS functionality and needs to be assigned an IP
address and managed independently.
The following figure shows an example of the console port on a 7210 SAS-Sx 1/10GE front panel for the
24-port variant.
Figure 14: Front panel: 7210 SAS-Sx 1/10GE 24-port variant
The following figure shows an example of the console port on a 7210 SAS-Sx 1/10GE front panel for the
48-port variant.
3HE 18197 AAAB TQZZA
© 2022 Nokia.
Use subject to Terms available at: www.nokia.com/terms/.
166
SPACER TEXT