7210 SAS-MXP, R6, R12, S, SX, T BASIC SYSTEM
CONFIGURATION GUIDE RELEASE 22.9.R1
System management
Description
This command provides the user a better control over the modules plugged into the 1830 CWDM device
slots. The user can preprovision acceptable modules by configuring the card-type parameter with the
appropriate card-type vwm-acronym. The modules are identified using the acronyms listed below.
The 7210 SAS validates the configured card-types with the card-type acronym retrieved from the clip-on
device and checks the following.
• If the configured card-type matches the card type acronym retrieved from the clip-on device, the
7210 SAS allows management of the module.
• If the configured card-type does not match the card type acronym retrieved from the clip-on device, the
7210 SAS raises an event to alert the user of mismatch in configuration. The event results in a major
alarm with the major LED set. In such a case, the card status displays ‟Provisioning Mismatch” error.
• The mismatch event/trap is cleared if the module is replaced with the one that has a correct card type
acronym. Any pending trap/event, major alarm and major LED is cleared.
If the user set the card to administratively up and the module is missing, the 7210 SAS raises an event/
trap. The event results in a major alarm with the major LED set to the appropriate color. If the user has
preprovisioned the card and administratively shut it down, the software does not attempt to match the
module’s identifier (if the module is equipped in the slot) and clears any pending alarms. The software
retrieves any information about the equipped module to aid the user with provisioning.
The no form of this command removes and clears the card-type information. Until the card-type is
provisioned, the software does not raise any events/traps/alarms for the card and clears all pending
events/traps/alarms/LEDs.
The following table lists the acronyms defined by the optical group. For more information, see the Product
overview guide for 1830 VWM. This is used to preprovision the acceptable modules that can be equipped
in the slots of the clip-on device.
Table 41: Card type acronyms for 1830 CWDM devices
Module description Acronym
1830 VWM 1-CH CWDM FILTER (AB VARIANT) - CH1 (1471nm) SFC1A
1830 VWM 1-CH CWDM FILTER (AC VARIANT) - CH1 (1491nm) SFC1B
1830 VWM 1-CH CWDM FILTER (AD VARIANT) - CH1 (1511nm) SFC1C
1830 VWM 1-CH CWDM FILTER (AE VARIANT) - CH1 (1531nm) SFC1D
1830 VWM 1-CH CWDM FILTER (AF VARIANT) - CH1 (1551nm) SFC1E
1830 VWM 1-CH CWDM FILTER (AG VARIANT) - CH1 (1571nm) SFC1F
1830 VWM 1-CH CWDM FILTER (AH VARIANT) - CH1 (1591nm) SFC1G
1830 VWM 1-CH CWDM FILTER (AI VARIANT) - CH1 (1611nm) SFC1H
1830 VWM 2-CH CWDM FILTER (AK VARIANT) - CH1,2 SFC2A&B
1830 VWM 2-CH CWDM FILTER (AL VARIANT) – CH3,4 SFC2C&D
1830 VWM 2-CH CWDM FILTER (AM VARIANT) – CH5,6 SFC2E&F
3HE 18197 AAAB TQZZA
© 2022 Nokia.
Use subject to Terms available at: www.nokia.com/terms/.
368
SPACER TEXT
To Next Page
Loading...