7210 SAS-MXP, R6, R12, S, SX, T BASIC SYSTEM
CONFIGURATION GUIDE RELEASE 22.9.R1
Boot options
The IP address should be entered in standard
dotted-decimal form with a network length.
example: 192.168.1.169/24
Existing eth-mgmt port settings are:
eth-mgmt-port
eth-mgmt-address xx.xxx.xx.xx/24 active
eth-mgmt-address xx.xxx.xx.xx/24 standby
eth-mgmt-address 0 active
eth-mgmt-address 0 standby
eth-mgmt-route x.x.x.x/24 next-hop xx.xxx.xx.x
eth-mgmt-route x.x.x.x/24 next-hop xx.xxx.xx.x
eth-mgmt-route xx.xxx.x.x/16 next-hop xx.xxx.xx.x
eth-mgmt-route xxx.x.x.x/8 next-hop xx.xxx.xx.x
eth-mgmt port is configured for Boot Interface Management,
Press ENTER to proceed with existing port settings
Or "disable" to disable the port for Boot Interface Management
Or "edit" to change the port settings: edit
You need to assign an IP address for this port.
The IP address should be entered in standard
dotted-decimal form with a network length.
example: 192.168.1.169/24
The existing eth-mgmt Active IP address is xx.xxx.xx.xx/24. Press ENTER to keep it.
Enter eth-mgmt Active IP Address : xx.xxx.xx.xx/24
In case of an IPv6, the IPv6 address should be
entered in standard colon hexadecimal notation
with a prefix length.
example: 3FFE::1/112
Enter eth-mgmt Active IPv6 Address (Type 0 if none desired): 0
The existing eth-mgmt Standby IP address is xx.xxx.xx.xx/24. Press ENTER to keep it.
Enter eth-mgmt Standby IP Address : xx.xxx.xx.xx/24
In case of an IPv6, the IPv6 address should be
entered in standard colon hexadecimal notation
with a prefix length.
example: 3FFE::1/112
Enter eth-mgmt Standby IPv6 Address (Type 0 if none desired): 0
You specified network locations which might require
static routes to reach. You will be asked to
enter static routes until all the locations become
reachable.
Static routes should be entered in the following format:
prefix/mask next-hop ip-address
example: 192.168.0.0/16 next-hop 192.168.1.254
A static route to the Primary Image exists: xxx.x.x.x/8 next-hop xx.xxx.xx.x
Do you want to keep it? (yes/no) y
Would you like to add a static route? (yes/no) yes
Enter ip route: xx.xxx.x.x/16 next-hop xx.xxx.xx.x
A route to that subnet already exists.
Would you like to add a static route? (yes/no) n
Would you like to add a static IPv6 route? (yes/no) n
Current configuration enables use of console (setting is "no console-disabled")
Press ENTER to proceed with existing setting or 'disable' to disable console access:
New Settings
------------
primary-image ftp://*:*@xxx.xxx.xx.xxx/tmp/sasr/b/
secondary-image cf1:\
tertiary-image uf1:\
primary-config uf1:\SASR2553.cfg
secondary-config uf1:\SASR2553.cfg
tertiary-config cf2:\SASR2553.cfg
#eth-mgmt Port Settings:
no eth-mgmt-disabled
eth-mgmt-address xx.xxx.xx.xx/24 active
eth-mgmt-address xx.xxx.xx.xx/24 standby
eth-mgmt-route x.x.x.x/24 next-hop xx.xxx.xx.x
3HE 18197 AAAB TQZZA
© 2022 Nokia.
Use subject to Terms available at: www.nokia.com/terms/.
159
SPACER TEXT
To Next Page
Loading...