Planet IGS-10020MT User Manual

User’s Manual of IGS-10020MT
MGB-TSX
SFP-Port 1000Base-SX mini-GBIC module - 550m (-40~75℃)
MGB-TLX
SFP-Port 1000Base-LX mini-GBIC module - 10km (-40~75℃)
MGB-TL30
SFP-Port 1000Base-LX mini-GBIC module - 30km (-40~75℃)
MGB-TL70
SFP-Port 1000Base-LX mini-GBIC module - 70km (-40~75℃)
Fast Ethernet SFP Transceiver Modules
MFB-FX SFP-Port 100Base-FX Transceiver (1310nm)-2km
MFB-F20 SFP-Port 100Base-FX Transceiver (1310nm)-20km
MFB-F40 SFP-Port 100Base-FX Transceiver (1310nm)-40km
MFB-F60 SFP-Port 100Base-FX Transceiver (1310nm)-60km
MFB-FA20 SFP-Port 100Base-BX Transceiver (WDM,TX:1310nm)-20km
MFB-FB20 SFP-Port 100Base-BX Transceiver (WDM,TX:1550nm)-20km
MFB-TFX SFP-Port 100Base-FX Transceiver (1310nm) -2km (-40~75 )℃
MFB-TF20
SFP-Port 100Base-FX Transceiver (1310nm) - 20km (-40~75℃)
It recommends using PLANET SFPs on the Industrial Managed Switch. If you insert a SFP
transceiver that is not supported, the Industrial Managed Switch will not recognize it.
1000Base-SX/LX:
Before connect the other switches, workstation or Media Converter.
1. Make sure both side of the SFP transceiver are with the same media type, for example: 1000Base-SX to 1000Base-SX,
1000Bas-LX to 1000Base-LX.
2. Check the fiber-optic cable type match the SFP transceiver model.
 To connect to 1000Base-SX SFP transceiver, use the Multi-mode fiber cable- with one side must be male duplex LC
connector type.
 To connect to 1000Base-LX SFP transceiver, use the Single-mode fiber cable-with one side must be male duplex LC
connector type.
Connect the fiber cable
1. Attach the duplex LC connector on the network cable into the SFP transceiver.
2. Connect the other end of the cable to a device – switches with SFP installed, fiber NIC on a workstation or a Media
Converter.
3. Check the LNK/ACT LED of the SFP slot on the front of the Industrial Managed Switch. Ensure that the SFP transceiver
is operating correctly.
100Base-FX:
Before connect the other switches, workstation or Media Converter.
40

Planet IGS-10020MT Specifications

General

Switch type	Managed
Switch layer	L2+
Quality of Service (QoS) support	Yes
SFP module slots quantity	2
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
10G support	No
Number of VLANs	255
Networking standards	IEEE 1588, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1ad, IEEE 802.1ag, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ah, IEEE 802.3bz, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Copper ethernet cabling technology	1000BASE-T, 100BASE-TX, 10BASE-T
Security algorithms	802.1x RADIUS, SSH, SSL/TLS
Throughput	14.8 Mpps
Jumbo frames	9000
MAC address table	8000 entries
Stackable	-
Certification	FCC Part 15 Class A, CE
Product color	Black
Housing material	Aluminum
International Protection (IP) code	IP30
Power consumption (typical)	10 W
Heat dissipation	34 BTU/h
Operating temperature (T-T)	-40 - 75 °C
Operating relative humidity (H-H)	5 - 95 %
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	87.8 mm
Width	56 mm
Height	135 mm
Weight	720 g