Siemens SIMATIC ET 200pro - Page 16

SIMATIC - ET 200pro motor starter
GWA 4NEB 950 5661-02 DS 04
xiv
Table 10-4: Thermal motor model – signals and actions . . . . . . . . . . . . . . . 10-9
Table 10-5: Thermal motor model – measured values and statistical data . . . 10-10
Table 10-6: Device parameters for current limits – settings . . . . . . . . . . . . 10-14
Table 10-7: Current limits – signals and actions . . . . . . . . . . . . . . . . . . . . 10-14
Table 10-8: Device parameters for temperature sensor – settings . . . . . . . . 10-16
Table 10-9: Temperature sensor – signals and actions . . . . . . . . . . . . . . . 10-17
Table 10-10: Device parameters for asymmetry – settings . . . . . . . . . . . . . 10-19
Table 10-11: Asymmetry – signals and actions . . . . . . . . . . . . . . . . . . . . . 10-19
Table 10-12: Asymmetry – measured values . . . . . . . . . . . . . . . . . . . . . . 10-19
Table 10-13: Description of 'Input n – action' . . . . . . . . . . . . . . . . . . . . . . 10-22
Table 10-14: Device parameters for inputs – settings . . . . . . . . . . . . . . . . . 10-24
Table 10-15: Inputs – signals and actions . . . . . . . . . . . . . . . . . . . . . . . . 10-25
Table 10-16: Device parameters for soft starter control function – settings . . . 10-27
Table 10-17: Device parameters for response to bus failure – settings . . . . . . 10-29
Table 10-18: Device parameters for mechanical braking – settings . . . . . . . . 10-32
Table 10-19: Mechanical braking – signal . . . . . . . . . . . . . . . . . . . . . . . . 10-32
Table 10-20: Self-test – test steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-33
Table 10-21: Self-test – signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-34
Table 10-22: Emergency start – commands . . . . . . . . . . . . . . . . . . . . . . . 10-35
Table 10-23: Emergency start – signal . . . . . . . . . . . . . . . . . . . . . . . . . . 10-35
Table 10-24: Factory setting – signals . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-36
Table 10-25: Device parameters for control function reversing starter – settings 10-38
Table 10-26: Control function reversing starter – signals . . . . . . . . . . . . . . . 10-38
Table 10-27: Electronic / mechanical switching technology – signals and actions 10-39
Table 10-28: Master control of the operating modes . . . . . . . . . . . . . . . . . 10-42
Table 10-29: Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-43
Table 10-30: Commands and their meanings . . . . . . . . . . . . . . . . . . . . . . 10-44
Table 10-31: Communication – signals . . . . . . . . . . . . . . . . . . . . . . . . . . 10-45
Table D-1: Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
Table D-2: Data record 68 – read / write process image of the outputs . . . . . D-6
Table D-3: Data record 69 – read process image of the inputs . . . . . . . . . . D-7
Table D-4: Data record 72 – logbook – device errors . . . . . . . . . . . . . . . . D-8
Table D-5: Signals in the logbook – device errors . . . . . . . . . . . . . . . . . . D-8
Table D-6: Data record 73 – read logbook – trips . . . . . . . . . . . . . . . . . . D-12
Table D-7: Read signals in the logbook – trips . . . . . . . . . . . . . . . . . . . . D-12
Table D-8: Data record 75 – read logbook – events . . . . . . . . . . . . . . . . . D-13
Table D-9: Read signals in the logbook – events . . . . . . . . . . . . . . . . . . . D-14
Table D-10: Data record 92 – read device diagnosis . . . . . . . . . . . . . . . . . D-15
Table D-11: Structure of the command data record . . . . . . . . . . . . . . . . . D-21
Table D-12: Data record 93 – write command . . . . . . . . . . . . . . . . . . . . . D-21
Table D-13: Data record 94 – read measured values . . . . . . . . . . . . . . . . . D-23
Table D-14: Data record 95 – statistical data . . . . . . . . . . . . . . . . . . . . . . D-25