Toshiba Strata CTX - Page 299

Telephone Button Programming
100 Series Programs
Strata CTX Programming - Part 3:Telephone Button Programming 04/03 13-21
Telephone Button
Programming
105-26 Call Button Jumping
)% , n, +ROG , +ROG
n = 1. Enable (default)
2. Disable
If enabled, line calls move from a telephone DN button to a line button
after they are answered. After the call is answered, the DN button is
cleared to receive another call. With this operation the DN acts as an
answer button for the telephone. This operation only applies if the line
that is answered has a CO, GCO, or Pooled line button appearance
on the telephone. If disabled, line calls remain on the DN after they
are answered.
106
Day/Night Mode Day
of Week Mapping
 , +ROG
The Day of the Week schedule defines each day as the type of day
the schedule shall follow. These types of days are called Work Day,
Non-work Day, and Holiday. Each day of the week can be classified.
106-01 Monday n = 1. Work Day (default)
2. Non-Work
3. Holiday
Enter the type of day to follow for daily schedule. 1- Work Day; 2-
Non-Work Day; or 3- Holiday.
106-02 Tuesday n = 1. Work Day (default)
2. Non-Work
3. Holiday
Enter the type of day to follow for daily schedule. 1- Work Day; 2-
Non-Work Day; or 3- Holiday.
106-03 Wednesday n = 1. Work Day (default)
2. Non-Work
3. Holiday
Enter the type of day to follow for daily schedule. 1- Work Day; 2-
Non-Work Day; or 3- Holiday.
106-04 Thursday n = 1. Work Day (default)
2. Non-Work
3. Holiday
Enter the type of day to follow for daily schedule. 1- Work Day; 2-
Non-Work Day; or 3- Holiday.
106-05 Friday n = 1. Work Day (default)
2. Non-Work
3. Holiday
Enter the type of day to follow for daily schedule. 1- Work Day; 2-
Non-Work Day; or 3- Holiday.
106-06 Saturday n = 1. Work Day
2. Non-Work (default)
3. Holiday
Enter the type of day to follow for daily schedule. 1- Work Day; 2-
Non-Work Day; or 3- Holiday.
106-07 Sunday n = 1. Work Day
2. Non-Work (default)
3. Holiday
Enter the type of day to follow for daily schedule. 1- Work Day; 2-
Non-Work Day; or 3- Holiday.
107
PAD Table
Assignment
 , +ROG
Assigns additional Sender and Receiver pad values to pad groups in
the pad table.
107-01 Sender PAD Device
Number
)% , n, +ROG
See “PAD Table” on
page 13-22.
n = Up to 3 digits
101~106 (CTX100)
101~110 (CTX670 Basic)
101~132 (CTX670 Exp.)
Enter Sender Pad Device Number from Pad Table.
107-02 Receiver PAD Device
Number
)% , n1, +ROG
n1 = Up to 3 digits
101~106 (CTX100)
101~110 (CTX670 Basic)
101~132 (CTX670 Exp.)
Enter Receiver Pad Device Number from Pad Table.
107-03 PAD Loss
)% , n2, +ROG , +ROG
n2 = 1. 6 dB Net Gain
2. 3 dB Net Gain
3. 0 dB
4. 3 dB Net Loss
5. 6 dB Net Loss
6. 9 dB Net Loss
7. 12 dB Net Loss
8. 15 dB Net Loss
Enter Pad Value (See PAD Table below). The value shown shows the
net effect.
Note To pad is to insert loss; therefore, negative loss equals net
gain.
Programs 103~107 (continued)
Button Sequence Value(s) Summary