Telephone Button Programming
300 Series Programs
Strata CTX Programming - Part 3:Telephone Button Programming 04/03 13-63
Telephone Button
Programming
316-01 Equipment Number
)%
, xxyyzz,
+ROG
xx =
yy =
zz =
xx = Cabinet 01, yy = 03,
05, or 07 and zz = Channel
01 is always used to assign
RPTU parameters
Enter the ISDN RPTU equipment number as xxyyzz:
Example: If the RPTU is installed in cabinet shelf 5, slot 3, enter
050301.
Cabinet numbers:
CTX100: Select 01 for Base and Expansion cabinet.
CTX670: Select 01 for Base and 02~07 respectively for each
Expansion cabinet.
Slot numbers:
CTX100: Select 01~04 for Base slots and 05~08 for Expansion slots.
CTX670: Select 01~08 for Base slots and 01~10 for Expansion slots..
or
xx = Cabinet 02~10,
yy = 01, 03, or 05 and
zz = Channel 01 is always
used to assign RPTU
parameters
316-02 Trunk ID
)%
, n,
+ROG
n = 0~126
(default = 1)
An identifier must be used as part of the addressing to communicate
with the PSTN which channel on which link is used the given call. This
identifier is assigned by the connected PSTN.
316-03 D Channel Provided
)%
, n,
+ROG
n = 1. D-Channel
2. No D-Channel (default)
If a backup ‘D’ Channel is to be used, it needs to be enabled.
316-04 Backup D Channel
Position
)%
, n,
+ROG
,
+ROG
n = 1~128
(default = 24)
Channel Group Number.
317
ISDN BRI Trunk
,
+ROG
The following program enables set up for ISDN related system
settings.
317-00 Channel Group
n,
+ROG
n = 1~32 (CTX100)
1~48 (CTX670 Basic)
1~128 (CTX670 Exp.)
Enter the BRI channel Group Number.
317-01 Equipment Number
)%
, xxyyzz,
+ROG
xx =
yy =
zz =
CTX670
Cabinet (01~07)
Slot (01~10)
Circuit (01~08 or 01~24)
Enter the equipment number xxyyzz to which the ISDN BRI Trunk is
to be assigned.
Example: If the RBUU is installed in cabinet shelf 5, slot 3, enter
050301 for circuit 1.
Cabinet numbers:
• CTX100 – Select 01 for Base and Expansion cabinet.
• CTX670 – Select 01 for Base and 02~07 respectively for each
Expansion cabinet.
Slot numbers:
• CTX100 – Select 01~04 for Base slots and 05~08 for Expansion
slots.
• CTX670 – Select 01~08 for Base slots and 01~10 for Expansion
slots.
or
CTX100
Cabinet (01)
Slot (01~08)
Circuit (01~04)
317-02 Protocol
)%
, n,
+ROG
n = 1. National ISDN
2. ETSI
3. TTC
4. National ISDN Nortel
Select the ISDN protocol. Only Bearer capabilities specified by the
protocol can be entered in this field. The Initial value for ISDN
Protocol corresponds to information set in the hardware level.
National ISDN = North America, ETSI = England and TTC = Japan.
317-03 ILG
)%
, n,
+ROG
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
ILG assignments must be made for basic ISDNs to process the calls
being received.
317-04 OLG
)%
, n,
+ROG
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
OLG assignments must be made for basic ISDNs to process the calls
being originated.
317-05 Connection Format
)%
, n,
+ROG
n = 1. Point to Point
2. Point to Multi Point
Identify connection format with the PSTN is 1- Point-to-Point or 2-
Point-to-Multipoint.
317-06 Bearer Svc - Speech
)%
, n,
+ROG
n = 1. Enable (default)
2. Disable
Enable speech capability.
Programs 316~317 (continued)
Button Sequence Value(s) Summary
To Next Page
Loading...
