Alcatel-Lucent OmniSwitch 6800 Series - Page 924

page -12 OmniSwitch 6800/6850/9000 Network Configuration Guide March 2008
bridged ports 8-27
designated bridge 8-6
flat operating mode 5-10, 8-12, 8-13
path cost 8-32
port connection types 8-36
Port ID 8-8
port ID 8-31
port path cost 8-6
port roles 8-7
port states 8-7, 8-35
root bridge 8-6, 8-22, 8-23, 8-24
root path cost 8-6
topology 8-6, 8-11
Topology Change Notification 8-9
Spanning Tree Bridge
defaults 8-3
Spanning Tree bridge parameters
802.1D standard protocol 8-19
802.1s multiple spanning tree protocol 3-1, 8-19
802.1w rapid reconfiguration protocol 8-19
automatic VLAN containment 8-26
forward delay time 8-24
hello time 8-22
maximum age time 8-23
priority 8-21
Spanning Tree Modes 3-11
1x1 mode 3-11
flat mode 3-11
Spanning Tree Port
defaults 8-4
Spanning Tree port parameters 8-27
connection type 8-36
link aggregate ports 8-30, 8-31, 8-33, 8-35, 8-37
mode 8-35
path cost 8-32
priority 8-31
specification
IPv6 7-2
Specifications
QoS 18-2
specifications
802.1AB 1-2
802.1Q 3-2
dynamic link aggregation 5-2
Ethernet 25-2
Ethernet OAM 9-2
GVRP 6-2
interswitch protocols 2-2
IP 6-2
IPX 12-2
Port Mapping 12-2
port mirroring 23-3
port monitoring 23-5, 23-7
RDP 9-2
RIP 8-2
RMON 23-10
Server Load Balancing 22-2
Spanning Tree 8-3
static link aggregation 4-2
switch health 23-12
switch logging 24-2
UDLD 26-2
VLAN rules 13-2
SPX 12-5
SSL
for LDAP authentication servers 13-28
policy servers 17-6
static agg agg num command 4-3, 4-9
static link aggregation 4-1
adding ports 4-9
application examples 4-3, 4-11
configuration steps 4-7
creating 4-8
defaults 4-2
deleting 4-8
deleting ports 4-9
disabling 4-10
enabling 4-10
group names 4-10
groups 4-5, 5-7
overview 4-5, 5-7
specifications 4-2
verify information about 4-12
static linkagg admin state command 4-10
static linkagg name command 4-10
static linkagg size command 4-3, 4-8
static MAC addresses 2-4
static route
IP 6-11, 7-16
IPX 12-8
metric 6-11, 7-16
subnet mask 6-11
static VLAN port assignment 11-4
subnet mask 6-11
switch health
application examples 23-13
defaults 23-13
monitoring 23-41
specifications 23-12
switch health statistics
resetting 23-47
viewing 23-46
switch logging
application examples 24-4
application ID 24-6
defaults 24-3
output 24-9
severity level 24-8
specifications 24-2
status 24-10
swlog appid level command 24-6
swlog clear command 24-11
swlog command 24-4, 24-6
swlog output command 18-21
swlog output command 24-9
swlog output flash file-size command 24-11