EasyManuals Logo

Brother MFC-8220 Service Manual

Brother MFC-8220
328 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #193 background imageLoading...
Page #193 background image
MFC-8220
SERVICE MANUAL
6-15
3.3.2 Causes & countermeasures
The causes for paper jam problems vary depending on the location of the paper jam. When a
paper jam occurs inside the machine, you have to find the location of the paper jam first,
remove the jammed paper and then take the appropriate countermeasure referring to the table
below;
Problem Type of Jam Cause Remedy
Jam when the
machine is turned
on.
Paper stuck The front regist
sensor or paper eject
sensor is turned on.
Remove the paper
inside the machine.
If there is no paper,
check the suspect
sensors referring to
‘3.9 Sensor
OperationaI Check
in Chapter 7.
Top of paper
stopped at 350mm
from the second exit
roller. Next paper is
not fed.
Jam caused by
paper length
detected as longer
than 400mm (16 in).
The front regist
sensor is not
returning properly
and is not turning off.
Check front regist
sensor motion
referring to ‘3.9
Sensor OperationaI
Check’ in Chapter 7.
Bottom of paper
stopped around the
transfer roller.
Jam caused by
paper length
detected as shorter
than 80mm.
The front regist
sensor was turned
off early.
Malfunction of
actuator or hardware
noise.
Check the front
regist sensor
referring to ‘3.9
Sensor OperationaI
Check’ in Chapter 7.
Top of paper
stopped between the
paper feed roller and
the pick-up roller.
Jam caused by a
paper feed delay.
Paper was not fed in
at the proper timing
due to paper dust or
wear of the rubber
pick-up roller.
Remove the paper
dust attached to the
pick-up roller. If the
rubber is worn out,
replace it with a new
one.
Top of paper
stopped at 50mm
from the contact
point of the heat
roller and pressure
roller.
Jam caused by the
paper not being
sensed when ejected
from the paper eject
sensor.
The paper eject
sensor is not working
properly and has not
turned off. (single
printing)
Check sensor motion
referring to ‘3.9
Sensor OperationaI
Check’ in Chapter 7.
Jam after paper is
ejected.
Jam caused by the
paper not being
sensed when ejected
from the paper eject
sensor.
The paper eject
sensor or front regist
sensor is not working
properly and has not
turned off.
(continuous printing)
Check sensor motion
referring to ‘3.9
Sensor OperationaI
Check’ in Chapter 7.

Table of Contents

Other manuals for Brother MFC-8220

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brother MFC-8220 and is the answer not in the manual?

Brother MFC-8220 Specifications

General IconGeneral
Typeall in one
Tray Capacity250
Automatic Document Feeder Capacity30 sheets
Paper Sizeletter, legal, a4, b5, a5, b6, a6, exe
Paper Handlingup to 250 sheets
Mono Print Speed21 pages per minute
Print Resolution Monoup to 2400 x 600
Maximum Number of Pages Per Monthup to 20, 000
Scanner Typesheetfed
Scan Resolutionup to 300 x 600
Copier Resolution Monoup to 600
Fax Functionyes
Cartridgesn/a
Number Of Cartridges2
Internal Memoryyes
Networknot applicable
Connectivityparallel, usb 2.0
OS Compatibilitypc: windows 95, 98, 98se, me, nt workstation 4.0, 2000 professional or xp, mac: os 8.6 to 9.2, os x 10.1, 10.2.1 to 10.3 or later, available usb 2.0 or parallel port
Mobile Devices Connectionno
Weight and Dimensions IconWeight and Dimensions
Height13.2 inches
Width17 inches
Net Weight25.6 pounds

Related product manuals