Tapered Brush Assembly Detailed
210999-008 Rev H RH
210999-007 Rev H LH
ITEM # QTY. PART# DESCRIPTION
1 1 611931 DIAL INDICATOR, 2-3/8 FACE, .25” RANGE
2 2 611932 COVER, TAPERED BRUSH ARM
3 1 612133 COVER, TAPERED BRUSH BACK, CB
4 2 611934 BRUSH, TAPERED 4-2 OD X 7.63, .010
5 4 611935 BEARING, 20MM ID X 37MM OD X 9MM
6 4 612028 SNAP RING, EXTERNAL, 20MM, SS
7 2 714034 NUT, PULLEY ADJUSTMENT
8 1 715700 PLATE, TAPERED BRUSHES MAIN
9 1 715701 PLATE, BRUSH ARM UPPER PIVOT
10 1 715702 PLATE, BRUSH ARM LOWER FIXED
11 2 715703 BLOCK, UPPER ARM PIVOT
12 1 715704 SHAFT, UPPER BRUSH ARM PIVOT
13 1 715705 BLOCK, LOWER ARM FIXED MOUNT
14 1 715706 BLOCK, T ARM MOUNT
15 1 715707 BLOCK, BRUSH ADJUST MAIN PLATE
16 1 715708 BLOCK, 5/16-18 ADJUST PIVOT
17 1 715709 BLOCK, 5/16-24 ADJUST PIVOT
18 1 715710 SHAFT, BRUSH ADJUSTMENT
19 1 715711 KNOB, BRUSH ADJUSTMENT
20 4 715712 SPACER, 5/8 HEX X 1-1/8L, 1/4-20
21 2 715713 SPACER, 5/8 OD X .257 ID X .3 L, AL
22 1 715714 BRACKET, TAPERED BRUSH PLUG MOUNT
23 1 715718 BAR, BRUSH INDICATOR MOUNT
24 1 715719 ANGLE, BRUSH INDICATOR STRIKE
25 1 715729 SHAFT, 20MM BRUSH, LH
26 1 715730 SHAFT, 20 MM BRUSH, RH
ITEM# QTY. PART# DESCRIPTION
27 2 715731 HUB, TAPERED BRUSH MNT, 20MM
28 2 715732 PULLEY, TAPERED BRUSH DRIVE, 20MM
29 6 715733 BUSH,MACH 20MM ID X 32MM OD X 1.91MM
30 2 955457 KEY SQ 3/16 X 1/2 .002 UNDER SIZE
31 6 955938 WASHER, LOCK 3/8” SST
32 4 955939 WASHER, LOCK 5/16” SST
33 13 955940 WASHER LOCK 1/4” SST
34 8 955941 WASHER LOCK #10 SST
35 4 955976 WASHER FLAT 5/16 SST
36 4 955977 WASHER FLAT 1/4” SST
37 4 955978 WASHER FLAT #10 SST
38 1 958612 PIN ROLL, 1/8 DIA X 3/4 SST
39 4 971308 SCREW SET SOC 1/4-28 UNF X 1/2 SST
40 2 975116 SCREW SHLDR 3/8 X 1, 5/16-18 SST
41 2 978908 SCREW SOC HD CAP #10-24 UNC X 1/2 SST
42 6 978910 SCREW SOC HD CAP #10-24 UNC X 5/8 SST
43 4 981712 SCREW FLT HD SOC 1/4-20 X 3/4 SST
44 6 982310 SCREW FLT HD SOC #10-24 X 5/8 SST
45 2 985724 SCREW BUTT HD SOC 1/4-20 X 1 1/2 SST
46 6 988916 SCREW FIN HEX 3/8-16 X 1 SST
47 2 989724 SCREW FIN HEX 5/16-18 X 1 1/2 SST
48 1 989748 SCREW FIN HEX 5/16-18 X 3 SST
49 1 989748L SCREW FIN HEX 5/16-18LH X 3 SST
50 5 989912 SCREW FIN HEX 1/4-20 X 3/4 SST
51 6 989916 SCREW FIN HEX 1/4-20 X 1 SST
52 4 C00111 BEARING, .75 OD X .25 ID X .28 W
13 14
FOLD OUT TO VIEW DRAWING
To Next Page
Loading...
