Dell Force10 MXL Blade - OSPF ACK Packing

364 | Open Shortest Path First (OSPFv2)
www.dell.com | support.dell.com
If you require the RFC 2328 flooding behavior, enable it by using the flood-2328 command in ROUTER
OSPF mode. When you enable RFC 2328 flooding, this command configures FTOS to flood LSAs on all
interfaces.
To confirm RFC 2328 flooding behavior, use
debug ip ospf packet command and look for output similar to
the following (Figure 20-4).
Figure 20-4. Enabling RFC-2328 Compliant OSPF Flooding
In FTOS version 7.5.1.0, to confirm that RFC-2328 compliant OSPF flooding is enabled, use the show ip
ospf
command (Figure 20-5).
Figure 20-5. Enabling RFC-2328 Compliant OSPF Flooding
OSPF ACK Packing
The OSPF ACK Packing feature bundles multiple LS acknowledgements in a single packet, significantly
reducing the number of ACK packets transmitted when the number of LSAs increases. This feature also
enhances network utilization and reduces the number of small ACK packets sent to a neighboring router.
OSPF ACK packing is enabled by default and is non-configurable.
00:10:41 : OSPF(1000:00):
Rcv. v:2 t:5(LSAck) l:64 Acks 2 rid:2.2.2.2
aid:1500 chk:0xdbee aut:0 auk: keyid:0 from:Vl 1000
LSType:Type-5 AS External id:160.1.1.0 adv:6.1.0.0 seq:0x8000000c
LSType:Type-5 AS External id:160.1.2.0 adv:6.1.0.0 seq:0x8000000c
00:10:41 : OSPF(1000:00):
Rcv. v:2 t:5(LSAck) l:64 Acks 2 rid:2.2.2.2
aid:1500 chk:0xdbee aut:0 auk: keyid:0 from:Vl 100
LSType:Type-5 AS External id:160.1.1.0 adv:6.1.0.0 seq:0x8000000c
LSType:Type-5 AS External id:160.1.2.0 adv:6.1.0.0 seq:0x8000000c
00:10:41 : OSPF(1000:00):
Rcv. v:2 t:4(LSUpd) l:100 rid:6.1.0.0
aid:0 chk:0xccbd aut:0 auk: keyid:0 from:TenGig 10/21
Number of LSA:2
LSType:Type-5 AS External(5) Age:1 Seq:0x8000000c id:170.1.1.0 Adv:6.1.0.0
Netmask:255.255.255.0 fwd:0.0.0.0 E2, tos:0 metric:0
LSType:Type-5 AS External(5) Age:1 Seq:0x8000000c id:170.1.2.0 Adv:6.1.0.0
Netmask:255.255.255.0 fwd:0.0.0.0 E2, tos:0 metric:0
Printed only for ACK packets
No change in update packets
FTOS#show ip ospf
Routing Process ospf 1 with ID 2.2.2.2
Supports only single TOS (TOS0) routes
It is an Autonomous System Boundary Router
It is Flooding according to RFC 2328
SPF schedule delay 5 secs, Hold time between two SPFs 10 secs
Number of area in this router is 1, normal 0 stub 0 nssa 1
--More--