Dell Force10 MXL Blade Configuration Guide

544 | Simple Network Management Protocol (SNMP)
www.dell.com | support.dell.com
SNMPv2-SMI::mib-2.47.1.1.1.1.2.158 = STRING: "Unit: 2 Port 27 10G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.159 = STRING: "Unit: 2 Port 28 10G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.160 = STRING: "Unit: 2 Port 29 10G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.161 = STRING: "Unit: 2 Port 30 10G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.162 = STRING: "Unit: 2 Port 31 10G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.163 = STRING: "Unit: 2 Port 32 10G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.164 = STRING: "40G QSFP+ port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.165 = STRING: "Unit: 2 Port 33 40G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.169 = STRING: "40G QSFP+ port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.170 = STRING: "Unit: 2 Port 37 40G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.174 = STRING: "Optional module 0"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.175 = STRING: "2-port 40G QSFP (XL)"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.176 = STRING: "Unit: 2 Port 41 40G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.180 = STRING: "Unit: 2 Port 45 40G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.184 = STRING: "Optional module 1"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.185 = STRING: "4-port 10GE SFP+ (XL) "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.186 = STRING: "Unit: 2 Port 49 10G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.187 = STRING: "Unit: 2 Port 50 10G Level"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.188 = STRING: "Unit: 2 Port 51 10G Level"
o SNMPv2-SMI::mib-2.47.1.1.1.1.2.189 = STRING: "Unit: 2 Port 52 10G Level
Troubleshooting SNMP Operations
When you use SNMP to retrieve management data from an SNMP agent on a Dell Force10 router, take
into account the following behavior:
• When you query an IPv4 icmpMsgStatsInPkts object in the ICMP table by using the
snmpwalk
command, the output for echo replies may be incorrectly displayed. To correctly display this
information under ICMP statistics, use the
show ip traffic command.
• When you query an icmpStatsInErrors object in the icmpStats table by using the
snmpget or snmpwalk
commands, the output for IPv4 addresses may be incorrectly displayed. To correctly display this
information under IP and ICMP statistics, use the
show ip traffic command.
• When you query an IPv4 icmpMsgStatsInPkts object in the ICMP table by using the
snmpwalk
command, the echo response output may not be displayed. To correctly display ICMP statistics, such
as echo response, use the
show ip traffic command.

Dell Force10 MXL Blade Specifications

General

Switching Capacity	1.28 Tbps
Forwarding Rate	952 Mpps
Product Type	Blade Switch
Latency	< 3 microseconds
Operating Temperature	0°C to 40°C (32°F to 104°F)
Redundancy	Yes
Management	CLI, SNMP, Web
Layer Support	Layer 2, Layer 3
Jumbo Frame Support	Up to 9216 bytes
Management Ports	1 x 10/100/1000 Mbps
Storage Temperature	-40°C to 70°C
Weight	4.5 kg (9.9 lbs)