Dell PowerConnect B-RX - Page 1436

1360 BigIron RX Series Configuration Guide
53-1002253-01
Quality of Service (QoS)
E
qos queue-type <queue-number> wred averaging-weight
<avg-weight>
“Setting the averaging-weight (Wq) parameter” on
page 489
qos queue-type <queue-number> wred drop-precedence
<policing-status> drop-probability-max
<p-max>
“Setting the maximum drop probability” on page 491
qos queue-type <queue-number> wred drop-precedence
<policing-status> max-avg-queue-size <max-size>
“Setting the minimum and maximum average queue
size” on page 491
qos queue-type <queue-number> wred drop-precedence
<policing-status> min-avg-queue-size <min-size>
“Setting the minimum and maximum average queue
size” on page 491
qos queue-type <queue-number> max-queue-size
<max-queue>
“Configuring the maximum instantaneous queue
size” on page 491
qos queue-type <queue-number> wred drop-precedence
<policing-status> packet-size-max <pkt-size>
“Setting the maximum packet size” on page 492
qos queue-type <queue-number> wred enable “Enabling WRED” on page 489
qos scheduler destination-weighted <queue0-weight>
<queue1-weight> <queue2-weight> <queue3-weight>
“Configuring WFQ destination-based traffic
scheduling” on page 496
qos scheduler enhanced-strict <queue0-rate>
<queue1-rate> <queue2-rate> <queue3-rate>
“Configuring enhanced strict priority-based traffic
scheduling” on page 495
qos scheduler max-rate <queue0-rate> <queue1-rate>
<queue2-rate> <queue3-rate>
“Configuring maximum rate-based traffic scheduling”
on page 496
qos scheduler min-rate <queue0-rate> <queue1-rate>
<queue2-rate> <queue3-rate>
“Configuring minimum rate-based traffic scheduling”
on page 497
qos scheduler source-weighted <queue0-weight>
<queue1-weight> <queue2-weight> <queue3-weight>
“Configuring WFQ source-based traffic scheduling”
on page 496
qos scheduler strict “Configuring strict priority-based traffic scheduling”
on page 495
qos-tos map cos-dscp <dscp0> <dscp1> <dscp2>
<dscp3> <dscp4> <dscp5> <dscp6> <dscp7>
“Changing the CoS –> DSCP mappings” on page 483
qos-tos map cos-priority <prio0>
<prio1><prio2><prio3><prio4><prio5><prio6> <prio7>
“Changing the DSCP –> internal forwarding priority
mappings” on page 484
qos-tos map dscp-dscp <old-dscp-value>
[<old-dscp-value>...]
to <new-dscp-value>
“Changing the DSCP –> DSCP mappings” on
page 483
qos-tos map dscp-priority <dscp-value> [<dscp-value> ...]
to <priority>
“Changing the DSCP –> internal forwarding priority
mappings” on page 484
qos-tos mark cos | dscp “Enabling marking” on page 482
qos-tos trust cos | dscp “Specifying trust level” on page 482
qos-tos “Enabling ToS-based QoS” on page 482
show qos multicast [port-no] “Displaying the multicast traffic engineering
configuration” on page 499
show qos scheduler “Displaying the scheduler configuration” on
page 497
show qos wred “Displaying the WRED configuration” on page 493
Commands See ...