566 Eos Family Operations Manual
Integrating Your App with Eos: Step 3 – Staying in Sync
Your app can now request all of the show data from Eos, but if a user is editing show data, your app
would become out of sync. The solution to this is to subscribe to Eos show data changes with the fol-
lowing command: /eos/subscribe = <uint32: X> (where 0=unsubscribe, 1=subscribe)
While subscribed, Eos will send the following commands when Eos show data changes:
In the reply, the first argument will be a sequence number, followed by a list of the targets that
changed. The targets are specified OSC Numbers and/or OSC Number Ranges
/eos/out/notify/patch/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/cuelist/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/cue/<cue list number>/list/<list index>/<list count> = <uint32: sequence num-
ber>, ...
/eos/out/notify/group/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/macro/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/sub/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/preset/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/ip/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/fp/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/cp/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/bp/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/curve/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/fx/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/snap/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/pixmap/list/<list index>/<list count> = <uint32: sequence number>, ...
/eos/out/notify/ms/list/<list index>/<list count> = <uint32: sequence number>, ...
When your app receives a notification that Eos show data has changed, you should then request
detailed information about the modified show data. You may request detailed show data via target
number or UID. (From the initial sync, you should be able to build a mapping of each type of show
data to correlate target number with UID)
Request detailed show data information via target number:
/eos/get/patch/<channel number> (Eos returns ALL parts)
/
e
o
s/
g
e
t
/
p
a
t
c
h
/
<c
h
a
n
n
e
l
n
u
m
b
e
r
>
/
<p
a
r
t
n
u
m
b
e
r
>
(specific channel part)/eos/get/cuelist/<cuelist number>
/eos/get/cue/<cuelist number>/<cuenumber> (Eos returns base cue and ALL parts)
/eos/get/cue/<cuelist number>/<cuenumber>/0 (base cue)
/eos/get/cue/<cuelist number>/<cuenumber>/<cue part number> (specific cue part)
/eos/get/group/<group number>
/eos/get/macro/<macro number>
/eos/get/sub/<sub number>
/
e
o
s/
g
e
t
/
p
r
e
s
e
t
/
<p
r
e
se
t
n
u
m
b
e
r
>
To Next Page
Loading...
Need help?
General
