HPE FlexNetwork 5130 HI SERIES User Manual

191
<Sysname> system-view
[Sysname] acl basic 2001
[Sysname-acl-ipv4-basic-2001] rule permit source 1.1.1.1 0.0.0.0
[Sysname-acl-ipv4-basic-2001] rule deny source any
[Sysname-acl-ipv4-basic-2001] quit
[Sysname] snmp-agent sys-info version v2c
[Sysname] snmp-agent group v2c readCom
[Sysname] snmp-agent usm-user v2c userv2c readCom acl 2001
# Add the user userv2c in the SNMPv2c group readCom so only the NMS at 1.1.1.2 can use the
protocol SNMPv2c and read-only community name userv2c to access the device.
[Sysname] acl basic name testacl
[Sysname-acl-ipv4-basic-testacl] rule permit source 1.1.1.2 0.0.0.0
[Sysname-acl-ipv4-basic-testacl] rule deny source any
[Sysname-acl-ipv4-basic-testacl] quit
[Sysname] snmp-agent sys-info version v2c
[Sysname] snmp-agent group v2c readCom
[Sysname] snmp-agent usm-user v2c userv2c readCom acl name testacl
Related commands
display snmp-agent community
snmp-agent community
snmp-agent group
snmp-agent usm-user v3
Use snmp-agent usm-user v3 to create an SNMPv3 user.
Use undo snmp-agent usm-user v3 to delete an SNMPv3 user.
Syntax
In non-FIPS mode:
• In VACM mode:
snmp-agent usm-user v3 user-name group-name [ remote { ipv4-address | ipv6 ipv6-address }]
[ { cipher | simple } authentication-mode { md5 | sha } auth-password [ privacy-mode { 3des |
aes128 | aes192 | aes256 | des56 } priv-password ] ] [ acl { ipv4-acl-number | name ipv4-acl-name }
| acl ipv6 { ipv6-acl-number | name ipv6-acl-name } ] *
undo snmp-agent usm-user v3 user-name { local | engineid engineid-string | remote
{ ipv4-address | ipv6 ipv6-address } }
• In RBAC mode:
snmp-agent usm-user v3 user-name user
-role role-name [ remote { ipv4-address | ipv6
ipv6-address } ] [ { cipher | simple } authentication-mode { md5 | sha } auth-password
[ privacy-mode { 3des | aes128 | aes192 | aes256 | des56 } priv-password ] ] [ acl
{ ipv4-acl-number | name ipv4-acl-name } | acl ipv6 { ipv6-acl-number | name ipv6-acl-name } ] *
undo snmp-agent usm-user v3 user-name { local | engineid engineid-string | remote
{ ipv4-address | ipv6 ipv6-address } }
In FIPS mode:
• In VACM mode:
snmp-agent usm-user v3 user-name group-name [ remote { ipv4-address | ip
v6 ipv6-address } ]
{ cipher | simple } authentication-mode sha auth-password [ privacy-mode { aes128 | aes192 |

HPE FlexNetwork 5130 HI SERIES Specifications

General

Product Series	HPE FlexNetwork 5130 HI Series
Switching Capacity	176 Gbps
Input Voltage	100-240V AC
MAC Address Table Size	32K
Management	Web, CLI, SNMP
Dimensions (W x D x H)	440 x 440 x 44 mm
Operating Temperature	0°C to 45°C
Operating Humidity	10% to 90% (non-condensing)
Routing Protocol	RIP, OSPF, BGP
VLANs	4096