innomar SBP smart - Page 9

User’s Manual INNOMAR Parametric Sub-Bottom Profilers / SESWIN 9
Innomar Technologie GmbH (2023-01) 9
7.5 How to install and set up a motion sensor ..................................................................... 98
7.5.1 Motion Sensor Installation .................................................................................................. 98
7.5.2 SESWIN Motion Sensor Setup ........................................................................................... 98
7.5.3 Motion Sensor Test............................................................................................................. 99
7.6 How to avoid interference with other acoustic systems ................................................ 100
7.6.1 Synchronizing / Triggering – General Remarks ............................................................... 100
7.6.2 Running the INNOMAR SBP triggered by a Multi Beam System ........................................ 101
7.7 How to synchronize a sparker at a fixed ping rate ....................................................... 105
7.8 How to to brodcast data from SESWIN to HYPACK
®
................................................... 106
7.9 How to broadcast data from SESWIN to Beamworx NavAQ
®
...................................... 109
7.10 How to use SESWIN’s documentation and report tools ............................................... 112
7.10.1 Document SESWIN system and interface settings .......................................................... 112
7.10.2 Log files for work reports / profile lists .............................................................................. 112
7.10.3 System information and LOG files for troubleshooting ..................................................... 113
7.11 How to reset to factory defaults ................................................................................... 113
7.12 How to remote-control an Innomar SBP ...................................................................... 114
7.12.1 Operating the Innomar system via KVM extender ............................................................ 114
7.12.2 Operating the Innomar system via RS232/Ethernet connection ...................................... 114
8 Maintenance and Error Handling....................................................................... 115
8.1 Hardware Handling and Maintenance .......................................................................... 116
8.1.1 Transducer ........................................................................................................................ 116
8.1.2 Transducer Visual Inspection ........................................................................................... 116
8.1.3 Hull-mounted Transducers ............................................................................................... 117
8.1.4 Topside Unit Handling ...................................................................................................... 117
8.1.5 Topside Unit Maintenance ................................................................................................ 117
8.1.6 System-Check .................................................................................................................. 118
8.2 Hardware Related Issues ............................................................................................ 119
8.2.1 The voltage indicators (LEDs) at the front panel are not illuminated ............................... 119
8.2.2 The internal display is switched off if an external monitor is connected ........................... 119
8.2.3 The internal display is white. The PC seems not to boot. ................................................ 119
8.3 SESWIN Error Messages at System Start ................................................................... 119
8.4 SESWIN Error and Warning Messages at System Setup ............................................ 121
8.5 Other SESWIN Error and Warning Messages ............................................................. 122
8.6 No incoming sensor data ............................................................................................. 124
8.6.1 No data or instable from the Motion Sensor ..................................................................... 124
8.6.2 No incoming position data ................................................................................................ 124
8.7 SESWIN functions seem not to work ........................................................................... 125
8.7.1 Transmitters can’t be switched on .................................................................................... 125
8.7.2 Changing the “Range” is impossible ................................................................................. 125
8.7.3 Data-Recording is not possible ......................................................................................... 125
8.7.4 The Output “Depth Out” does not work ............................................................................ 125
8.8 Signal detection problems ........................................................................................... 126
8.8.1 No seafloor on the screen ................................................................................................ 126
8.8.2 The echo signal is too small ............................................................................................. 126
8.9 Firmware Update ......................................................................................................... 127
9 Innomar NetViewer Software ............................................................................. 131
10 Innomar SES-Convert Software ......................................................................... 133
10.1 Example data at Innomar’s ISE post-processing software ........................................... 133
10.2 Convert Innomar data into SEG-Y format using SESCONVERT .................................. 134
10.2.1 SEG-Y Conversion Settings ............................................................................................. 135
10.2.2 SEG-Y Processing Settings .............................................................................................. 136
10.2.3 Data Conversion ............................................................................................................... 137
10.3 Checking the SEG-Y files ............................................................................................ 138
10.4 Store / Reload Conversion Settings ............................................................................. 138
11 Innomar ISE Post-Processing Software ........................................................... 139
12 Data Acquisition and Post-Processing Workflow ............................................ 141
12.1 Survey preparation and survey line planning ............................................................... 141