Lenze L-force 9400 Series - Page 356

9400 regenerative power supply module | Parameter setting
Index
356 L EDS94ARNExxxx EN 2.3 - 06/2014
LS_LineInterface 261
LS_SyncInput 264
M
Mains connection 84
Mains frequency (C00051) 276
Mains not connected (error message) 230
Mains voltage (C00052) 276
Mains voltage (C00173) 287
Mains voltage 10% too high (error message) 230
Mains voltage 10% too low (error message) 229
Mains voltage 15% too high (error message) 230
Mains voltage 15% too low (error message) 229
Mains voltage is switched off (error message) 241
Mains voltage is switched on (error message) 241
Masked Error number (C00162) 285
Master functionality (CAN) 110
Maximum current (C00022) 276
Maximum effective power (C00057) 277
Memory module
Faulty file system (error message)
214
File system has been formatted (error message) 230
File system has been restored (error message) 230
Memory module DIP switches 101
Memory module has been changed (error message)
213
Memory module has been removed (error message)
211
Memory module is defect or missing (error message)
210, 212
Memory module is missing (error message) 209
Minimum brake resistance (C00134) 282
MM440 328, 329
Monitoring 196
MXI1
CAN module is missing or incompatible (error
message)
239
Ethernet module is missing or incompatible (error
message)
238
ICM module is missing or incompatible (error
message)
239
Module changed during operation (error message)
210
Module has been changed (error message) 213
Module is defect or missing (error message) 211
Module is missing or incompatible (error message)
238
PROFIBUS module is missing or incompatible (error
message)
238
Wrong module (error message) 212
MXI2
CAN module is missing or incompatible (error
message)
239
Ethernet module is missing or incompatible (error
message)
239
ICM module is missing or incompatible (error
message)
239
Module changed during operation (error message)
210
Module has been changed (error message) 213
Module is defect or missing (error message) 211
Module is missing or incompatible (error message)
238
PROFIBUS module is missing or incompatible (error
message)
238
Wrong module (error message) 212
N
Network management telegram (NMT) 109
New applications loaded (error message) 218
NMT (network management) 109
No heartbeat signal detected (error message) 242
No parameter for module in MXI1 (error message) 241
No parameter for module in MXI2 (error message) 241
No. of CRC cycles (C00618) 321
Node address 105
Node guarding event 137
Node guarding protocol 134
Node ID 105
Node life time 136
O
Output power (DC) (C00050) 276
P
Parameter set
Type of standard device has been changed (error
message)
241
Version conflict (error message) 241
Parameter set faulty (error message) 239
Parameter set loaded (error message) 240
Parameter set restored (error message) 240
Parameter set saved (error message) 240
PDO delay 118
PDO mapping (MXI1)
Configuration is faulty (error message)
220
PDO mapping (MXI2)
Configuration is faulty (error message)
220
Phase currents (C00055) 277
PLC configuration invalid (error message) 221, 228,
231
Pointer access in impermissible memory area (error
message)
219
Position value faulty (error message) 244
Power control
Task overflow (error message)
226
Power section incompatible (error message) 212
Power section is defect (error message) 210, 211, 229
Power stage has been changed (error message) 213
Power-on time meter (C00179) 287
Pre-defined error field (I-1003) 148
Producer heartbeat time (I-1017) 154