SMAR CD600 Plus - Section 4 Function Blocks Library

SMAR CD600 Plus

198 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Section 4

FUNCTION BLOCKS LIBRARY

4.1

Table of Contents

Default Chapter5
- Table of Contents5
Section 1 - Operation9
- Cd600 Plus Front Panel9
- Loop Selection10
- Alarm Acknowledgment10
- Changing the Alphanumeric Display Bright11
Section 2 - Tuning13
Section 3 - Programming15
- Operation15
  - Typical Description of a Block15
  - The Loops16
- Tags16
- How to Program the Cd600 Plus16
- Example of a Configuration16
Section 4 - Function Blocks Library21
- Function Table22
- Function 01 - Analog Input (Ai)23
  - Operation23
- Function 02 - Current Output (Co)24
  - Operation24
- Function 03 - Voltage Output (Vo)25
  - Operation25
- Function 04 - Digital Input (DI)26
  - Operation26
- Function 05 - Digital Output (Do)27
  - Operation27
- Function 06 - Front View (Fv)28
  - Operation28
- Function 07 - Local/Remote Sp Selector (L/R)30
  - Operation30
- Function 08 - Automatic/Manual Station (A/M)33
  - Operation33
- Function 09 - Advanced Pid (Pid)37
  - Operation37
- Function 10 - Simple Pid (Pid)46
  - Operation46
- Function 11 - Step Controller (Step)50
  - Operation50
- Function 12 - Multiplier-Divider-Adder-Subtractor (Arth)53
  - Operation53
- Function 13 - Square Root (Sqr)57
  - Operation57
- Function 14 - Linearization (Lin)58
  - Operation58
- Function 15 - Derivative / Lead-Lag (Ll)60
  - Operation60
- Function 16 - Pressure and Temperature Compensation (Ptc)63
  - Operation63
- Function 17 - Polynomial (Pol)67
  - Operation67
- Function 18 - Totalization (Tot)69
  - Operation69
- Function 19 - Pulse Totalization Input (P/DI)71
  - Operation71
- Function 20 - Batch Comparator (Bat)75
  - Operation75
- Function 21 - Setpoint Generator (Spg)76
  - Operation76
- Function 22 - Double Alarm (Alm)78
  - Operation78
- Function 23 - Limiter with Alarm (Limt)80
  - Operation80
- Function 24 - Logic (Log)83
  - Operation83
- Function 25 - Timer (Tmr)85
  - Operation85
- Function 26 - High/Low Selector (H/L)87
  - Operation87
- Function 27 - Internal/External Selector (Ssel)88
  - Operation88
- Function 28 - Constant Adjuster (Adj)89
  - Operation89
- Function 29 - Input Selector (Isel)90
  - Operation90
- Function 30 - Output Selector (Osel)91
  - Operation91
- Function 31 - Linearization Curve (Pnt)92
  - Operation92
- Function 32 - General Visualization (Gv)95
  - Operation95
- Function 33 - Constants (K)96
  - Operation96
- Function 34 - Scan (Scn)97
  - Operation97
- Function 35 - Scan/Actuation of the Parameters Pid (Prm)99
  - Operation99
- Function 36 - Actuation (Atu)100
  - Operation100
- Function 37 - Digital Input with Timer Control (Dit)103
  - Operation103
- Control Function Blocks105
Section 5 - Resident Configuration107
Section 6 - Calibration113
- Analog Input (Ai)113
- Analog Input Calibration-Automatic Mode114
- Calibration of Analog Inputs - Manual Mode114
- Current Output (Co)115
- Voltage Output (Vo)116
Section 7 - Communication117
- Introduction117
- Controller Address117
- Baud-Rate118
- Time Cycle Adjustment118
- Opc Supervision119
- Serial Communication Network120
- Ethernet Communication Network120
Section 8 - Technical Specifications121
- Power Supply and Consumption121
- Integral Power Supply for Transmitters121
- Nvram (Non-Volatile Ram)121
- Analog Inputs and Outputs121
- Digital Inputs (Di1 to Di8)121
- Digital Outputs (Do1 to Do8)122
- Installation Conditions124
- Front Panel124
- Rear Panel Diagram125
Section 9 - Installation131
- Initial Inspection131
- Cd600 Versus Cd600 Plus137
- Introduction141
- Main Features141
Section 10 - System Installation143
- System Requirements143
- Installation143
Section 11 - Operation145
- Project Files145
- Importing a Project File147
- Exporting the Configuration147
- Printing Documents147
- Print Configuration148
- Print Preview149
Section 12 - Conf600 Plus Interface151
- Naming Loops151
- Main Toolbar152
- Drawing Toolbar152
- Ordering Toolbar153
- Alignment Toolbar153
- Color Palette154
- Document Properties154
- Object Properties157
- Document Properties Toolbar157
- Communications Toolbar157
- Selecting the Language157
- Converting the Configuration List to Graphics157
- Look Edition158
Section 13 - Resident Configuration159
Section 14 - Project Configuration161
- Activating the Block List161
- Adding Blocks to the Block List161
- Adding Blocks to the Drawing Area162
- Dragging Blocks on the Drawing Area163
- Adding the Communication Block163
- Changing Block Parameters164
- Deleting Blocks164
- Changing the Block Format165
Section 15 - Linking Blocks167
- Creating a Direct Link167
- Creating a Link with Interruption168
- Creating a Communication Link169
- Editing the Link Properties170
- Redrawing a Link170
- Removing a Link170
Section 16 - Communication171
- Checking the Controller171
- Configuring the Communication171
- Initializing the Communication172
- Uploading the Device Configuration173
- Downloading the Configuration to the Device174
- Showing Communication Values174
- Monitoring the Parameters of a Block175
- Updating the Configuration175
Section 17 - Calibration177
- Analog Input177
- Analog Input Calibration - Automatic Mode178
- Analog Input Calibration - Manual Mode179
- Current Output180
- Voltage Output180
Section 18 - Conf600 Plus Tutorial181
- Starting the Configurator182
- Creating a New Configuration182
- Building the Strategy182
  - Adding Blocks182
  - Moving Blocks184
- Linking Function Blocks184
- Creating All Links185
- Redrawing Links185
- Checking the Environment186
Appendix A - Quick Guide of Installation187
- Tools and Equipments Necessary for the Installation187
- Procedures187
- Returning Materials193
Appendix B193
- Fsr - Service Request Form195
Appendix C - Smar Warranty Certificate197

Other manuals for SMAR CD600 Plus

Quick Installation Guide5 pages