Effect parameter list
339
Appendix
Appendix
8: LoReso (LOW RESOLUTION)
1 Mod Depth 0~127 Modulation depth
2 Mod Delay Offset 1~127 Modulation delay offset
3 Mod Feedback -64~+63 Feedback amount
4 Resolution 1, 1/2~1/128 Resolution
5 Mod Mix Balance 0~127 Balance between modulation sound and modulation bypass sound
6 Phase Inverse R off, wet, wet+dry Left/right phase reversal
7 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance between dry sound and effect sound
9: Noisy (NOISY)
1 Drive 0~127 Degree of distortion
2 Mod Depth 1~10 Modulation depth
3 Mod Speed 0~127 Modulation speed
4 Mod Feedback -63~+63 Feedback amount
5 AM Speed 0.00Hz~39.7Hz Amplitude modulation frequency
6 AM Depth 0~127 Amplitude modulation depth
7 Mod Mix Balance 1~127 Balance between noise modulated sound and bypass sound
8 LPF Frequency 1.0kHz~Thru Frequency at which the low pass filter will cut the high range
9 LPF Resonance 1.0~12.0 Resonance of the low pass filter
10 EQ Frequency 100Hz~10.0kHz Frequency at which the EQ will boost/cut the mid range
11 EQ Gain -12~+12dB Gain by which the EQ will boost/cut the mid range
12 EQ Width 1.0~12.0 Width of the mid range area which the EQ will boost/cut
13 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance between the dry sound and effect sound
10: AtkLoFi (ATTACK LOFI)
1 Sensitive 0~127 Sensitivity
2 Resolution 1, 1/2~1/32 Resolution
3 Peak Frequency 100Hz~10.0kHz Frequency at which a peak will be created in the mid range
4 LPF Frequency 1.1kHz~Thru Frequency at which the low pass filter will cut the high range
5 Flanger Speed 0.00Hz~39.7Hz Frequency of delay modulation
6 Flanger LFO Wave tri, sine, saw up, saw down Modulation waveform selection
7 Flanger Depth 0~127 Modulation depth
8 Fln Depth Ofst R -64~+63 R ch offset for depth
9 Flanger Delay 0.1~650ms Delay time
10 Fln Delay Ofst R -884~0 R ch offset for delay time
11 Flanger Feedback -63~+63 Feedback amount
12 Flanger FB Ofst R -63~+63 R ch offset for feedback
13 Flanger FB HiDamp 0.1~1.0 Adjust the high range attenuation (low values will cause the high range to decay
faster)
14 FB HiDamp Ofst R -0.9~+0.9 R ch offset for high damp
15 Fln Mix Balance 1~127 Balance between flanger sound and bypass sound
16 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance between dry sound and effect sound
11: Radio (RADIO)
1 Noise Level 0~127 Degree of noise modulation
2 Tone 0~127 Tone of noise modulation
3 Mod LPF Frequency 1.0kHz~Thru Frequency at which the low pass filter will cut the high range
4 Mod HPF Resonance 1.0~12.0 Resonance of high pass filter
5 HPF Frequency Thru~8.0kHz Frequency at which the high pass filter will cut the low range
6 LPF Frequency 1.0kHz~Thru Frequency at which the low pass filter will cut the high range
7 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance between dry sound and effect sound
12: TurnTbl (DIGITAL TURNTABLE)
1 Click Density 0~5 Frequency with which the click sounds will occur
2 Click Level 0~127 Level of the click sounds
3 Noise Tone 0~6 Tone of noise
4 Noise Mod Speed 0.00Hz~39.7Hz Amplitude modulation frequency of the noise
5 Noise Mod Depth 0~127 Amplitude modulation depth of the noise
6 Dry Send to Noise 0~127 Mixture of dry signal into the noise
7 Noise LPF Freq 1.0kHz~Thru Frequency at which the low pass filter will cut the high range
8 Noise LPF Q 1.0~12.0 Low pass filter resonance
9 Noise Level 0~127 Noise level
10 Dry LPF Frequency 1.0kHz~Thru Frequency at which the low pass filter will cut the high range
11 Dry Level 0~127 Level of the dry sound
To Next Page
Loading...
Need help?
General
