Effect parameter list
340
Appendix
13: Jump (JUMP)
1 Depth 0~127 Modulation depth
2 Speed 0~127 Modulation speed
3 Direction L<>R, L>>R Modulation type
4 Type typeA, typeB, typeC Modulation type
5 Jump Wave Type typeA, typeB, typeC, typeD Modulation type
6 Resolution 1, 1/2~1/256 Resolution
7 LPF Frequency 1.0k~Thru Frequency at which the low pass filter will cut the high range
8 HPF Frequency Thru~8.0kHz Frequency at which the high pass filter will cut the low range
9 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance between the dry sound and effect sound
14: BeatChg (BEAT CHANGE)
1 BeatChange(Ctrl) -63~+63 Special parameter which allows a controller to modify the beat change
2 Beat Range 0~12 Width of variation for sample playback speed
3 PitchChange(Ctrl) -63~+63 Special parameter which allows a controller to modify the pitch change
4 Pitch Range 0~12 Width of variation for Pitch Change
5 Accuracy Type sound4~normal~rhythm4 Balance between emphasis on sound quality and emphasis on sense of beat
6 EQ Frequency 100Hz~10.0kHz Frequency at which the EQ will boost/cut the mid range
7 EQ Gain -12~+12dB Gain by which the EQ will boost/cut the mid range
8 EQ Width 1.0~12.0 Width of the area in which the EQ will boost/cut the mid range
9 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance between the dry sound and effect sound
• You can use this effect to set up a controller so that the controller will vary the playback speed while leaving the pitch unchanged. To set this up, first
select the program, then go the program’s EfType page (☞121) and set one of the program effects (Effect 1, 2, or 3) to BeatChg. Then go to the program’s
PgmCtl page (☞136), select the desired controller (Device), and set its Function to EF
x
-1 (where x is the Effect number: 1, 2, or 3). Then go to the effects
editing page (☞124) and set this effect’s Beat Range parameter to an appropriate value. Leave the BeatChange (Ctrl) and PitchChange (Ctrl) values set to
0, so that the effect operates only in response to the controller input.
• Note that this effect may not operate as expected if you apply it to the input signal or if you select it for more than one of the A3000’s three effect blocks.
15: VceCncl (VOICE CANCELLER)
1 Low Adjust 0~26 Adjust the frequency of the lower limit of the mid range that will be attenuated.
2 High Adjust 0~26 Adjust the frequency of the upper limit of the mid range that will be attenuated.
16: 3BandEQ 3 BAND EQ)
1 EQ Low Frequency 50Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
2 EQ Low Gain -12~+12dB Amount of gain by which the EQ will boost/cut the low range
3 EQ Mid Frequency 100Hz~10.0kHz Frequency at which the EQ will boost/cut the low range
4 EQ Mid Gain -12~+12dB Amount of gain by which the EQ will boost/cut the mid range
5 EQ Mid Width 1.0~12.0 Width of the area in which the EQ will boost/cut the mid range
6 EQ High Gain -12~+12dB Amount of gain by which the EQ will boost/cut the high range
7 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
8 Input Mode mono/stereo Mono/stereo input mode selection
17: Exciter (AURAL EXCITER) Aural Exciter is a registered trademark of Aphex Systems, Ltd., and is manufactured under license.
1 HPF Cutoff Freq 500Hz~16.0kHz Frequency at which the high pass filter will cut the low range of the effect sound
2 Drive 0~127 Degree with which the exciter effect will be applied
3 Mix Level 0~127 Level at which the effect sound will be mixed into the dry sound
18: AWah+Drum Set (AUTO WAH + DIST), 19: AWah+OD (AUTO WAH+ODRV)
1 LFO Frequency 0.00Hz~39.7Hz Frequency at which the wah filter will be controlled
2 LFO Depth 0~127 Depth at which the wah filter will be controlled
3 Cutoff Freq Offset 0~127 Offset value for the wah filter control frequency
4 Resonance 1.0~12.0 Bandwidth of the wah filter
5 Drive 0~127 (Distortion) Degree of distortion
6 PostDrive EQ Low -12~+12dB (Distortion) Gain by which the EQ will boost/cut the low range
7 PostDrive EQ Mid -12~+12dB (Distortion) Gain by which the EQ will boost/cut the mid range
8 PostDrive LPF Freq 1.0kHz~thru (Distortion) Frequency at which the filter will cut the high range
9 Drive Output Level 0~127 (Distortion) Output level
10 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
11 EQ Low Gain -12~+12dB Amount of gain by which the EQ will boost/cut the low range
12 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
13 EQ High Gain -12~+12dB Amount of gain by which the EQ will boost/cut the high range
14 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance between the dry sound and effect sound
To Next Page
Loading...
Need help?
General
