Cisco 7925G Administration Guide

Configuration ReferenceDescriptionFeature
For more information, see the Cisco Unified
Communications Manager System Guide,
“Cisco Unified IP Phones” chapter.
Detects and prevents Call Forward All loops. When a Call
Forward All loop is detected, the Call Forward All
configuration is ignored and the call rings through.
Call forward all loop
breakout
For more information, see the Cisco Unified
Communications Manager System Guide,
“Cisco Unified IP Phones” chapter.
Prevents a user from configuring a Call Forward All destination
directly on the phone that creates a Call Forward All loop or
that creates a Call Forward All chain with more hops than the
existing Forward Maximum Hop Count service parameter
allows.
Call forward all loop
prevention
For more information, see:
•
Cisco Unified Communications
Manager Administration Guide
•
Cisco Unified Communications
Manager System Guide, “Cisco Unified
IP Phones” chapter
Allows you to specify information that appears on a phone
when a call is forwarded. This information can include the
caller name, caller number, redirected number, and original
dialed number.
Call forward
configurable display
For more information, see Cisco Unified
Communications Manager System Guide,
“Cisco Unified IP Phones” chapter.
Allows you to override Call Forward All in cases where the
Call Forward All target places a call to the Call Forward All
initiator. This feature allows the Call Forward All target to
reach the Call Forward All initiator for important calls. The
override works whether the Call Forward All target phone
number is internal or external.
Call forward
destination override
For more information, see:
•
Cisco Unified Communications
Manager System Guide, “Cisco Unified
IP Phones” chapter
•
Cisco Unified Communications
Manager Features and Services Guide,
“Call Park” chapter
Allows users to park (temporarily store) a call and then retrieve
the call by using another phone in the Cisco Unified
Communications Manager.
Call park
For more information, see:
•
Cisco Unified Communications
Manager Features and Services Guide,
“Call Pickup Group Configuration”
chapter
•
Cisco Unified Communications
Manager System Guide, “Cisco Unified
IP Phones” chapter
•
Cisco Unified Communications
Manager Administration Guide, “Cisco
Unified IP Phone Configuration” chapter
Allows users to redirect a call that is ringing on another phone
within their pickup group to their phone.
You can configure an audio and visual alert for the primary
line on the phone. This alert notifies the users that a call is
ringing in their pickup group.
The audio and visual alert is only available for phones
on Cisco Unified Communications Manager Release
4.2 and later.
Note
Call pickup
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
151
Features, Templates, Services, and Users
Telephony Features Available

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g