Cisco 7925G Administration Guide

Configuration ReferenceDescriptionFeature
For more information, see Cisco Unified
Communications Manager System Guide,
“Cisco Unified IP Phones” chapter.
Allows a user to press a single Transfer softkey and then go
on-hook to complete a call transfer.
Onhook call transfer
For more information, see Cisco Unified
Communications Manager Features and
Services Guide, “Call Pickup Group
Configuration” chapter.
Allows a user to answer a call ringing on a phone in another
group that is associated with the user's group.
Other group pickup
No configuration required.Enables zero-touch provisioning of the wireless phones that
use Protected Extensible Authentication Protocol (PEAP) with
Server Validation.
PEAP with Server
Validation
Provisioning
Enhancement
For more information, see Cisco Unified
Communications Manager Features and
Services Guide, “Presence” chapter.
Allows a user to monitor the call state of another directory
number (DN) listed in call logs, speed-dials, and corporate
directories. The Busy Lamp Field (BLF) for the DN displays
the call state.
Presence-enabled
directories
For more information, see:
•
Cisco Unified Communications
Manager Administration Guide, “Cisco
Unified IP Phone Configuration” chapter
•
Cisco Unified Communications
Manager System Guide, “Cisco Unified
IP Phones” chapter
•
Cisco Unified Communications
Manager Features and Services Guide
“Barge and Privacy” chapter
Enables a user to allow or disallow other users of shared-line
devices to view the device all information or to enable another
user to barge into its active call.
Privacy
For more information, see Services Menu,
on page 167.
Requires an XML application to provide Push
to Talk service.
Allows users to call a target phone number or group and
announce a message (similar to a two-way radio) by using a
configurable applications button.
Push to Talk
For more information, see:
•
Cisco Unified Communications
Manager System Guide, “Cisco Unified
IP Phones” chapter
•
Cisco Unified Communications
Manager Features and Services Guide,
“Quality Report Tool” chapter
Allows users to use the QRT softkey on a phone to submit
information about problem phone calls. QRT can be configured
for either of two user modes, depending upon the amount of
user interaction desired with QRT.
Quality Reporting
Tool (QRT)
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
159
Features, Templates, Services, and Users
Telephony Features Available

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g