Send documentation comments to mdsfeedback-doc@cisco.com
20-13
Cisco MDS 9000 Family Troubleshooting Guide, Release 3.x
OL-9285-05
Chapter 20 Troubleshooting IP Storage Services
FCIP Issues
MDS2(config-if)# peer-info ipaddr 10.10.10.2
Mar 10 21:43:01 ips: Dequeued mts msg MTS_OPC_IPS_FCIP_CMI_REQUEST(mts opc 3321, msg id
32616)
Mar 10 21:43:01 ips: FCIP28: Process tunnel configuration event
Mar 10 21:43:01 ips: FCIP28: Change Peer IP from 0.0.0.0 to 10.10.10.2 and port from 3225
to 3225
Mar 10 21:43:01 ips: FCIP28: Queueing Set tunnel param event to tunnel FSM resource: 0
Mar 10 21:43:01 ips: Locked fcip_if_fsm for MTS_OPC_IPS_FCIP_CMI_REQUEST(msg id 32616)
Mar 10 21:43:01 ips: FCIP28: Send tunnel params to LC to DPP: 7
Mar 10 21:43:01 ips: Dequeued mts msg MTS_OPC_IPS_FCIP_SET_LC_TUNNEL_PARAM(mts opc 1897,
msg id 7358)
Mar 10 21:43:01 ips: Hndlr MTS_OPC_IPS_FCIP_SET_LC_TUNNEL_PARAM (mts_opc 1897 msg_id 7358)
Mar 10 21:43:01 ips: In handler : Received resp code: 0
Mar 10 21:43:01 ips: FCIP28: Received the tunnel params from LC
Mar 10 21:43:01 ips: FCIP28: Update the tunnel param and save to PSS
Mar 10 21:43:01 ips: FCIP28: add to admin pss
Mar 10 21:43:01 ips: FCIP28: add to run-time pss
Mar 10 21:43:01 ips: FCIP28: log: 2087000 phy: 2087000 state: 1 syslog: 0
Mar 10 21:43:01 ips: Unlocked fcip_if_fsm for MTS_OPC_IPS_FCIP_CMI_REQUEST(msg id 32616)
MDS2(config-if)#
MDS2(config-if)# no shutdown
MDS2(config-if)# Mar 10 21:43:32 ips: Dequeued mts msg
MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE(mts opc 3114, msg id 32737)
Mar 10 21:43:32 ips: Hndlr MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE (mts_opc 3114 msg_id
32737)
Mar 10 21:43:32 ips: Dequeued mts msg MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE(mts opc
3114, msg id 32778)
Mar 10 21:43:32 ips: Hndlr MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE (mts_opc 3114 msg_id
32778)
Mar 10 21:43:32 ips: Dequeued mts msg MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE(mts opc
3114, msg id 32783)
Mar 10 21:43:32 ips: Hndlr MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE (mts_opc 3114 msg_id
32783)
Displaying the Debug Output from FCIP Tunnel Supervisor Using the CLI
The following example shows the debug output from the supervisor of the FCIP tunnel.
MDS2(config)# interface fcip 28
MDS2(config-if)# no shutdown
MDS2(config-if)# Mar 10 22:59:46 ips: fu_priority_select: - setting fd[3] for select call
- found data in FU_PSEL_Q_CAT_MTS queue, fd(3), usr_q_info(1)
Mar 10 22:59:46 ips: fu_priority_select_select_queue: round credit(0)
Mar 10 22:59:46 ips: curr_q - FU_PSEL_Q_CAT_CQ, usr_q_info(3), priority(4), credit(0),
empty
Mar 10 22:59:46 ips: Starting a new round
Mar 10 22:59:46 ips: fu_priority_select: returning FU_PSEL_Q_CAT_MTS queue, fd(3),
usr_q_info(1)
Mar 10 22:59:46 ips: Dequeued mts msg MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE(mts opc
3114, msg id 47540)
Mar 10 22:59:46 ips: ips_mts_hdlr_pm_logical_port_state_change_range:
Mar 10 22:59:46 ips: Hndlr MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE (mts_opc 3114 msg_id
47540)
Mar 10 22:59:46 ips: fu_fsm_execute_all: match_msg_id(0), log_already_open(0)
Mar 10 22:59:46 ips: fu_fsm_execute_all: null fsm_event_list
Mar 10 22:59:46 ips: fu_fsm_engine: mts msg
MTS_OPC_PM_LOGICAL_PORT_STATE_CHANGE_RANGE(msg_id 47540) dropped
To Next Page
Loading...
Need help?
General