EasyManuals Logo

Cisco 9134 - MDS Multilayer Fabric Switch User Manual

Cisco 9134 - MDS Multilayer Fabric Switch
560 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #391 background imageLoading...
Page #391 background image
Send documentation comments to mdsfeedback-doc@cisco.com
20-17
Cisco MDS 9000 Family Troubleshooting Guide, Release 3.x
OL-9285-05
Chapter 20 Troubleshooting IP Storage Services
FCIP Issues
Verifying the Establishment of Default TCP Connections for Each Configured FCIP Tunnel Using the
CLI
Verify that two default TCP connections are established for each FCIP tunnel configured, one for control
traffic and one for data traffic.
MDS1# show ips stats tcp interface gigabitethernet 2/8
TCP Statistics for port GigabitEthernet2/8
Connection Stats
6 active openings, 8 accepts
6 failed attempts, 0 reset received, 8 established
Segment stats
295930 received, 1131824 sent, 109 retransmitted
(Excessive retransmits indicate possible core drops and/or that the TCP window size should be adjusted.)
0 bad segments received, 0 reset sent
TCP Active Connections
Local Address Remote Address State Send-Q Recv-Q
10.10.10.2:3225 10.10.11.2:65519 ESTABLISH 0 0
(This is used for F control traffic only.)
10.10.10.2:3225 10.10.11.2:65521 ESTABLISH 87568 0
(Send-Q increasing during read-only test.)
10.10.10.2:3225 0.0.0.0:0 LISTEN 0 0
(The TCP listen port is ready for new TCP connections.)
You can use the following command to verify that traffic is incrementing on the Gigabit Ethernet port of
the FCIP tunnel.
MDS1# show ips stats mac interface gigabitethernet 2/8
Ethernet MAC statistics for port GigabitEthernet2/8
Hardware Transmit Counters
1074898 frame 1095772436 bytes
0 collisions, 0 late collisions, 0 excess collisions
0 bad frames, 0 FCS error, 0 abort, 0 runt, 0 oversize
Hardware Receive Counters
33488196 bytes, 298392 frames, 277 multicasts, 16423 broadcasts
0 bad, 0 runt, 0 CRC error, 0 length error
0 code error, 0 align error, 0 oversize error
Software Counters
298392 received frames, 1074898 transmit frames
0 frames soft queued, 0 current queue, 0 max queue
0 dropped, 0 low memory
Verifying the Statistics of the ASIC Chip on Each Gigabit Ethernet Port Using the CLI
Traffic statistics can be verified on the internal ASIC chip on each Gigabit Ethernet port.
MDS1# show ips stats flamingo interface gigabitethernet 2/8
Flamingo ASIC Statistics for port GigabitEthernet2/8
Hardware Egress Counters
2312 Good, 0 bad protocol, 0 bad header cksum, 0 bad FC CRC
(Good frames and CRC error frames can be monitored.)
Hardware Ingress Counters
(Verify good increments on the active tunnel.)
2312 Good, 0 protocol error, 0 header checksum error
0 FC CRC error, 0 iSCSI CRC error, 0 parity error

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 9134 - MDS Multilayer Fabric Switch and is the answer not in the manual?

Cisco 9134 - MDS Multilayer Fabric Switch Specifications

General IconGeneral
BrandCisco
Model9134 - MDS Multilayer Fabric Switch
CategorySwitch
LanguageEnglish

Related product manuals