EasyManuals Logo

Cisco 9134 - MDS Multilayer Fabric Switch User Manual

Cisco 9134 - MDS Multilayer Fabric Switch
560 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #299 background imageLoading...
Page #299 background image
Send documentation comments to mdsfeedback-doc@cisco.com
14-21
Cisco MDS 9000 Family Troubleshooting Guide, Release 3.x
OL-9285-05
Chapter 14 Troubleshooting Zones and Zone Sets
Enhanced Zoning Issues
switch4(config)# no zoneset activate name excal2 vsan 1
Zoneset Deactivation initiated. check zone status
Step 2 Use the show zoneset active command to confirm that the zone set has been removed.
Step 3 Use the shut down command to shut down the connection to the zone to be merged.
switch4(config)# interface port-channel 1
switch4(config-if)# shutdown
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface fc1/14 is down
(Channel admin down)
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface fc1/15 is down
(Channel admin down)
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface fc1/16 is down
(Channel admin down)
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_PORT_CHANNEL_MEMBERS_DOWN: Interface
port-channel 1 is down (No operational members)
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_ADMIN_DOWN: Interface port-channel 1 is down
(Administratively down)
Nov 19 10:26:10 switch4 %LOG_PORT_CHANNEL-5-FOP_CHANGED: port-channel 1: first operational
port changed from fc1/16 to none
Step 4 Use the no shutdown command to reactivate the connection to the zone to be merged:
switch4(config-if)# no shutdown
Nov 19 10:28:11 switch4 %LOG_PORT_CHANNEL-5-FOP_CHAN
GED: port-channel 1: first operational port changed from none to fc1/15
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_UP: Interface port-channel 1 is up in mode TE
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/14, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/15, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/16, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/14, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/15, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/16, vsan 1 is up
Step 5 Use the show zoneset active vsan-id commands to exit configuration mode and check the active zone
sets.
switch4# show zoneset active
zoneset name wall vsan 1
zone name excal1 vsan 1
* fcid 0x620200
fcid 0x6200ca
zone name $default_zone$ vsan 1
* fcid 0x6e00da
* fcid 0x6e00d9
* fcid 0x6e00d6
* fcid 0x6e0100
After deactivating the zone set on switch 4 and performing a shutdown followed by a no shutdown on
the ISL that connects it to switch 3, the zone merge is processed again. Because switch 3 has no active
zone set, it learns the active zone set from switch 4 during the zone merge process.
Enhanced Zoning Issues
Enhanced zoning uses a session locking facility like CFS to prevent simultaneous zoning configuration
changes by two users on the same or separate switches. When a user starts to make a zoning change on
one switch for a VSAN, that switch will lock the fabric to prevent others from making zoning changes.
The user must issue a commit to make the changes active and release the fabric wide lock.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 9134 - MDS Multilayer Fabric Switch and is the answer not in the manual?

Cisco 9134 - MDS Multilayer Fabric Switch Specifications

General IconGeneral
BrandCisco
Model9134 - MDS Multilayer Fabric Switch
CategorySwitch
LanguageEnglish

Related product manuals