GAI-Tronics Elemec3 - IPAP Button Properties

To Next Page

To Previous Page

Pub. 42004-550C

Elemec3 Console Manual—Version 3 Page 38 of 109

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-550C.docx

07/21

Figure 39. Import Access Panel Button Layout

IPAP Button Properties

Use the IPAP BUTTON PROPERTIES pane to configure the buttons on each button page for the current

IPAP.

Figure 40. IPAP Button Properties

There are two BUTTON FUNCTIONS at the right end of the IPAP BUTTON PROPERTIES pane:

• Copy IPAP Button—copies the configuration of the currently selected button on the button screen.

• Paste IPAP Button—pastes the copied configuration to the currently selected button.

Main Page

Default Chapter1
- Table of Contents1
- G a I - T R O N I C S8
Confidentiality Notice8
Introduction8
The Programming Process8
- Process Flow9
- E3 Console Process Flow9
  - Elemec3 Console Manual-Version10
  - Figure 11. System Properties10
Install the E3 Console Application14
Run the E3 Console Application14
- Figure 1. Create New or Load Existing Configuration14
- Manage Configurations15
  - Figure 2. Manage Configurations15
  - LOCAL CONFIGURATIONS (Working Directory)15
- Create New Configuration16
- Create New Configuration from Template17
- Load an Existing Configuration17
- System-Wide Functions18
System Properties19
- Globals19
- Locations22
- Ack/Cancel Configuration22
- User Flags24
- System Flags24
  - Figure 16. Manage User Flags24
  - Figure 17. Manage System Flags24
- Manage Global Mutes25
- Global Audio MIX Setup25
  - Figure 18. Manage Global Mutes25
  - Figure 19. Global Audio MIX Setup26
Amplifiers27
- Figure 20. Amplifiers Summary27
- Figure 21. Add Amplifier27
- D600I, D300I, and D550I Power Amplifier Properties28
- GAI (Generic Amplifier Interface) Properties29
  - Figure 25. Hot Standby Setup30
- Hot Standby Amplifiers30
- Add Speaker Master31
  - Figure 26. Speaker Mater Setup31
Speaker Masters31
- Remove Speaker Master32
- Figure 27. Speaker Master Properties32
Speaker Remotes33
- Add Speaker Remotes33
  - Figure 28. Create Speaker Remotes33
  - Figure 29. Speaker Remotes Setup33
- Remove Speaker Remote34
Access Panel Interfaces Summary35
- Access Panel Interface Type Selection35
  - Figure 30. Access Panels Interfaces Summary35
  - Figure 31. Access Panel Interface Type Selection35
- Add Access Panels36
  - Figure 32. Add Access Panel36
- Access Panel Properties37
  - Figure 33. Access Panel Properties37
- Access Panel Button Configuration39
  - Figure 35. Access Panel Button Configuration39
  - Figure 36. IP Access Panels Summary42
IP Access Panels42
- Figure 37. IP Access Panel Properties43
- IP Access Panel Properties43
- IPAP Buttons44
Aplite HUBBCOM48
- Figure 43. AP Lite Profiles48
- Aplite HUBBCOM Access Panel Creation49
- Aplite Button Creation49
  - Figure 44. Aplite Profile Builder49
- AP Lite Properties50
  - Figure 45. Access Panel Button Appearance50
  - Figure 46. AP Lite Properties50
I/O Controllers51
- IP Controller Built-In I/O51
- Add I/O Controllers52
- I/O Controller Properties53
  - Inputs Tab55
  - Outputs Tab56
- Inhibit Groups57
  - Add Inhibit Groups58
  - Inhibit Group Builder58
- Output Behaviors59
- Output Groups59
Modbus60
- Terminology60
- Modbus TCP Server61
  - Inputs Tab61
  - Outputs Tab62
- External Modbus TCP Devices63
  - Inputs Tab64
  - Outputs Tab65
Audio Inputs66
- Sources Enabled66
- Page/Party Audio Input Properties67
- Telephone Interface Audio Input Properties68
- Voip Telephone Interface Setup69
- Auxiliary Inputs #1-5 Audio Input Properties72
- IP Aux #1-8 Audio Input Properties73
Zones74
- Add Zones74
- Zone Builder75
Playback Audio76
- Playback Audio Configuration77
- Messages79
  - Message Properties79
  - Message Builder79
System Events81
- Add Event81
- Events81
- Event Builder82
- Event Groups88
Scheduled Events89
Fault Reporting91
Voip Parameters92
- System Ip92
  - Aux IP Inputs92
  - Aux IP Outputs/Monitor out93
- Ip Destinations93
- Add Ip Destination94
SP2 Integration94
- Configuration Parameter Field Flags95
- Parameter Panes96
- Station Parameter Configuration and Precedence96
- I/O States97
- System Properties Screen98
- Groups Screen98
- Stations Screen99
- Profiles Screen101
- Parameter Panes102
- SP2 Configuration Assets110
- Find Station and Station List Utility112
Reference Documentation114
Save the Configuration114
Glossary of Terms115

GAI-Tronics Elemec3 - IPAP Button Properties

Table of Contents

Related product manuals