IBM i 830

Chapter 5. Locations, Addresses, and Part Listings
Locations and Addresses .........705
StartHereforLocationsInformation ....705
Locations — Models 830, SB2 System Unit with
FC 9074 Base I/O Tower ........709
Locations — Models 840, SB3 System Unit with
Processor Tower and FC 9079 Base I/O Tower . 719
Locations — FC 8079 I/O Tower ......735
Locations — FC 5074 I/O Tower ......736
Locations — FC 5075 I/O Tower ......740
Locations — FC 5078, 0578 PCI Expansion Unit 743
Locations — FC 5079 I/O Tower ......747
Locations — Integrated xSeries Adapter Card
(IXA), Formerly the Adapter for Netfinity Server 748
Locations — Power Distribution Unit (PDU) . . 750
Addresses — Models 830, SB2 System Unit with
FC 9074 Base I/O Tower ........750
Addresses — Models 840, SB3 Processor Tower
and FC 9079 Base I/O Tower .......758
Addresses — FC 5074 I/O Tower......766
Addresses — FC 5075 I/O Tower......775
Addresses — FC 5078/0578 PCI Expansion Unit 776
Addresses — FC 5079 I/O Tower......778
Addresses — for External xSeries Server, iSeries
Adapter — Machine Type 1519 ......778
I/O Adapters ............779
2890 Integrated xSeries Server (IXS) ....779
Power and Signal Cables ........779
Model 830 and Model SB2 with FC 9074 . . 780
Model 830 and Model SB2 with FC 9074 –
Dual Line Cord...........783
Model840andModelSB3.......786
FC 5074 and FC 5079 I/O Tower .....795
FC 5075 I/O Tower .........799
FC 5078, 0578 I/O Tower .......801
Part Assemblies ............802
Assembly 1: Models 830 and SB2 with FC 9074 –
Cover Assembly ............804
Assembly 2: Models 830 and SB2 with FC 9074 –
Final Assembly, Front ..........806
Assembly 3: Models 830 and SB2 with FC 9074 –
Final Assembly, Rear ...........814
Assembly 4: Models 830 and SB2 with FC 9074 –
Control Panel Assembly ..........824
Assembly 5: Models 840 and SB3 Processor Tower
– Cover Assembly ............826
Assembly 6: Models 840 and SB3 Processor Tower–
Final Assembly, Front ..........828
Assembly 7: Models 840 and SB3 Processor Tower
– Final Assembly, Rear ..........832
Assembly 8: Models 840 and SB3 – Control Panel,
Processor Tower ............838
Assembly 9: FC 9079 Tower (Models 840 and SB3)
– Cover Assembly ............840
Assembly 10: FC 9079 Tower (Models 840 and SB3)
– Final Assembly ............842
Assembly 11: Cover Assembly — FC 5074 ....852
Assembly 12: Final Assembly — FC 5074 ....854
Assembly 13: Cover Assembly – FC 5075 ....864
Assembly 14: Final Assembly – FC 5075 ....866
Assembly 15: Cover Assembly — FC 5078 ....870
Assembly 16: Final Assembly – FC 5078/0578 . . 872
Assembly 17: Cover and Hardware Assembly For
— FC 5079, FC 8079, FC 0550, FC 0551, 0578 . . . 876
Assembly 18: Power Distribution Unit (PDU)
Assembly For — FC 5079, FC 8079, FC 0550, FC
0551, 0578 ..............878
Cables and Miscellaneous .........879
External Cables............879
Assembly 19: External Cables ........880
InternalCables............882
Miscellaneous ............882
Assembly 20: Miscellaneous ........884
Type, Model, and Part Number list ......885
Model 830/SB2 – Processor Feature Codes and
CCINs...............890
Power Cord Part Numbers and Receptacle
Descriptions ..............891
Locations and Addresses
Start Here for Locations Information
This procedure describes how to find the correct diagram to use in this section.
1. Is the Frame ID 1, or is the direct select address 0001xxxx, or is the SRC B4xx
or B1xx?
Yes No
↓ Go to step 3 on page 706 of this procedure.
2. The hardware is located in the system unit. Find the model number. When in
manual mode, the system displays the model number in function 20 in pxxx
cccc format, where xxx is the model number.
© Copyright IBM Corp. 2000, 2001 705