Korg TRITON proX User Manual

iii
This “Parameter Guide” contains explanations and other
information regarding the operations of the parameters and
settings on the TRITON proX, TRITON pro, and TRITON.
The explanations are organized by mode, page, and tab.
Explanations and other information on the effects and their
parameters are also provided for each effect.
Refer to this guide when an unfamiliar parameter appears in
the display, or when you need to know more about a partic-
ular function.
Conventions in this manual
References to the TRITON proX, TRITON pro, and TRITON
The TRITON proX, TRITON pro, and TRITON are collec-
tively referred to in this manual as the TRITON.
Switches and knobs [ ]
References to the switches, dials, and knobs on the TRI-
TON’s panel are enclosed in square brackets [ ]. References
to
buttons or tabs indicate objects in the LCD display
screen.
Parameters in the LCD display screen “ “
Parameters displayed in the LCD screen are enclosed in
double quotation marks “ “.
Boldface type
Parameter values are printed in boldface type.
Content that is of particular importance is also printed in
boldface type.
Procedure steps 1 2 3 ...
Steps in a procedure are listed as 1 2 3 ...
☞ p. ■ , ☞■ – ■
These indicate pages or parameter numbers to which you
can refer.
Link ■ – ■
Link indicates a linked parameter on a different page that
has the same name or an abbreviated name.
■ – ■ indicates
the parameter numbers.
Symbols , , , , ,
These symbols respectively indicate cautions, advice, MIDI-
related explanations, a parameter that can be selected as an
alternate modulation source, a parameter that can be
selected as a dynamic modulation source, and a parameter
that can use the BPM/MIDI Sync function.
Example screen displays
The values of the parameters shown in the example screens
of this manual are only for explanatory purposes, and may
not necessary match the values that appear in the LCD
screen of your instrument.
MIDI-related explanations
CC# is an abbreviation for Control Change Number.
In explanations of MIDI messages,
numbers in square
brackets [ ]
always indicate hexadecimal numbers.
How to read the “Parameter Guide”
(example)
About this manual
Program P5: Edit-Common LFO
5–1: OSC1 LFO1 ( )
5–1
5–1a
5–1b
5–1c
5–1a: OSC1 LFO1
Waveform [Triangle 0…Random6 (Vector)]
▼ 5–1: Page Menu Command
0–1A
5–1A
5–1A: Swap LFO 1&2
Here you can make settings for the LFO that can be used to
cyclically modulate the Pitch, Filter, and Amp of oscillators 1
and 2. There are two LFO units for each oscillator. By setting
the LFO1 or LFO2 Intensity to a negative (–) value for Pitch,
Filter, or Amp, you can invert the LFO waveform.
Make settings for the “OSC1 LFO1,” which is the first LFO
that can be used for oscillator 1.
Select the LFO waveform.
This command exchanges the settings of LFO1 and 2. If LFO2
has been selected as Frequency Modulation AMS1 or 2 of
LFO1, that setting will be cancelled for LFO2 after the LFO1
and 2 settings have been exchanged. If this is selected from
the OSC1 LFO1 or OSC1 LFO2 tab, the LFO1 and LFO2 of
OSC1 will be exchanged.
1 Select this command to open the dialog box.
2 Press the OK button.
5–2: OSC1 LFO2
Here you can make settings for the OSC1 LFO2, which is the
second LFO that can be applied to oscillator 1. (☞“5–1: OSC1
LFO1”) However in “Frequency Modulation” (5–1b), the
LFO cannot be selected as a modulation source in “AMS1” or
“AMS2.”
5–3: OSC2 LFO1
This can be used when “Oscillator Mode” (1–1a) is set to
Double.
Here you can make settings for the OSC2 LFO1, which is the
first LFO that can be applied to oscillator 2. (☞“5–1: OSC1
LFO1”)
Mode name
Page No.
Tab No.
Tab name (1)
Parameter
number
Parameter
name
Tab name (2)
Page menu command
Page menu command No.
Page menu
command name
Range of possible
parameter values

Korg TRITON proX Specifications

General

Brand	Korg
Model	TRITON proX
Category	Synthesizer
Language	English