Sequencer
P0
P1 P2 P3 P4 P5 P6 P7 P8 P9
65
2 Select this command to open the following dialog box.
3 In “From Measure” and “To Measure,” specify the range
of measures that will be repeated. (By default, “From
Measure” and “To Measure” will be set to the range you
specified in the Track Edit tab.)
4 In “Times,” specify the number of repetitions. For exam-
ple if you set “From Measure” to 001, “To End of Mea-
sure” to 004, and “Times” to 2, the musical data of
measures 1–4 will be inserted into measures 5–8. The
result will be that measures 1–4 will be played twice.
5 If you wish to repeat the musical data of all tracks includ-
ing the master track, check “All Tracks.”
6 To execute the Repeat Measure command, press the OK
button. To cancel, press the Cancel button.
5–1J: Copy Measure
This command copies measures of musical data from the
copy source to the specified measure location.
When you execute the Copy Measure command, the track
data at the copy destination will be rewritten.
1 Select the copy source song.
2 Select this command to open the following dialog box.
3 In “From: Track,” select the copy source track. (By
default, this will be the track you selected in “Track
Select.”)
If you check “All Tracks,” the musical data of all tracks
including the master track will be copied.
4 In “From Measure” and “To Measure,” specify the range
of copy source measures. (By default, “From Measure”
and “To Measure” will be the range that you specified in
the Track Edit tab.)
5 In “To: Song,” specify the copy destination song. In
“Track” (when “All Tracks” is unchecked) specify the
copy destination track. In “Measure,” specify the first
measure where the copied measures will be inserted.
6 To execute the Copy Measure operation, press the OK
button. To cancel, press the Cancel button.
5–1K: Move Measure
This command moves measures of musical data to a speci-
fied destination. When you execute the Move Measure com-
mand, musical data following the move source will be
moved forward according to the number of measures
moved, and musical data following the move destination
will be moved backward correspondingly.
1 Select this command to open the following dialog box.
2 In “From: Track,” select the move source track. (By
default, this will be the track you selected in “Track
Select.”)
If you check “All Tracks,” musical data of all tracks
including the master track will be moved.
3 In “From Measure” and “To End of Measure,” specify the
range of measures that will be moved. (By default, “From
Measure” and “To End of Measure” will be the range that
you specified in the Track Edit tab.)
4 In “To: Track” (if “All Tracks” is unchecked), specify the
move destination track. In “Measure,” specify the first
measure of the move destination.
5 To execute the Move Measure command, press the OK
button. To cancel, press the Cancel button.
5–1L: Create Ctrl Data (Create Control Data)
This command gradually varies continuous-type data (e.g.,
control change, after touch, pitch bend, tempo) in the speci-
fied area.
1 In “Track Select,” select the track on which you wish to
perform the Create Control Data command. If you wish
to create tempo data, select Master Track as the track. In
this case, the step
4 item “Kind” will be set to “Tempo.”
2 Select this command to open the following dialog box.
3 Specify the range into which the control data will be
inserted. In “From Measure” and “To End of Measure”
specify the measures, and in “Beat.Tick” specify the beat
and clock. “ (By default, “From Measure” and “To End of
Measure” will be set to the range you specified in the
Track Edit tab.)
4 In “Kind,” select the type of musical data (events) that
you wish to create: Control Change, After Touch, or
Pitch Bend.
For Control Change, you can also select the control
change number (
☞p.223).
5 In “Start Value,” select the starting value of the control
data. In “End Value,” select the ending value of the con-
trol data. By default, the “Start Value” will be set to the
value of the existing data at the start location. If you wish
to create control data that changes smoothly from the
starting location, you can leave the “Start Value”
unchanged, and set only the “End Value.”
Track 1
1 2
3 4
5 6
1 2
3 4
1 2
3 4
5 6
Track 1
Before
Repeat
Measure
After
Repeat
Measure
If you execute the Repeat Measure operation on measures 1–4 with “Time” = 2,
measures 1–4 will be inserted into measures 5–8.
Track 1
(source)
2 (4/4)1 (4/4) 5 (3/4)4 (3/4)3 (4/4)
Track 2
(destination)
6 (3/4) 7 (4/4)
Example: When you copy measures 5–7 of track 1 to the third measure of track 2,
measures 3–5 of track 2 will be rewritten.
2 (4/4)1 (4/4) 5 (3/4)4 (3/4)3 (4/4) 6 (3/4) 7 (4/4)
To Next Page
Loading...
