SICK microScan3 Pro I/O User Manual

46. How the restart interlock works (4): the reset pushbutton must be pressed before
r
estarting the machine...............................................................................................72
47. Electrical diagram of external device monitoring (EDM).......................................... 73
48. Prevent crawling beneath...........................................................................................86
49. Prevent stepping over.................................................................................................86
50. Remove the system plug from below.........................................................................88
51. Remove the cover plate from the rear.......................................................................88
52. Installing the rear system plug...................................................................................89
53. Mounting the safety laser scanner directly...............................................................89
54. Connection of the OSSDs of an OSSD pair...............................................................91
55. No potential difference between load and protective device ................................. 91
56. Pin assignment of the voltage supply (male connector, M12, 4-pin, A-coded)...... 92
57. Alternative FE connection.......................................................................................... 92
58. Network pin assignment (M12 female connector, 4-pin, D-coding)....................... 93
59. Pin assignment of local inputs and outputs 1 (female connector, M12, 17-pin, A-
coded)..........................................................................................................................93
60. Pin assignment of dynamic control input (female connector, M12, 8-pin, A-coded)
..................................................................................................................................... 95
61. Pin assignment of inputs and outputs 2 (female connector, M12, 17-pin, A-coded)
..................................................................................................................................... 95
62. Software controls........................................................................................................98
63. Configuration............................................................................................................ 101
64. Overview....................................................................................................................102
65. Functional scope...................................................................................................... 104
66. Network settings: EFI-pro.........................................................................................105
67. Identification.............................................................................................................107
68. Application................................................................................................................ 110
69. Monitoring plane...................................................................................................... 111
70. Reference contour field............................................................................................116
71. Field editor................................................................................................................118
72. Field set template.....................................................................................................122
73. Background image................................................................................................... 123
74. Editing fields using coordinates.............................................................................. 125
75. Area that cannot be monitored............................................................................... 126
76. Enable propose field................................................................................................ 127
77. Inputs and outputs, local.........................................................................................131
78. Monitoring cases...................................................................................................... 135
79. Simulation.................................................................................................................140
80. Data output...............................................................................................................141
81. Report....................................................................................................................... 144
82. Alignment about the transverse axis...................................................................... 150
83. Alignment about the depth axis.............................................................................. 150
84. Status LEDs.............................................................................................................. 151
85. LEDs.......................................................................................................................... 152
86. Status LEDs.............................................................................................................. 153
87. Network LEDs........................................................................................................... 153
88. Fixing screws for the optics cover............................................................................161
89. Replacing the system plug.......................................................................................165
90. Pushbuttons on the device......................................................................................166
91. Fault display..............................................................................................................168
92. Data recorder............................................................................................................172
93. Event history............................................................................................................. 173
94. Message history....................................................................................................... 175
95. Switch-off tests......................................................................................................... 188
96. Duration and time offset for the switch-off tests in an OSSD pair........................189
97. Scanning range and object size for warning fields (devices with a max. protective
field range of 4.0 m and devices with max. protective field range of 5.5 m).......190
LIST OF FIGURES 19
8025424/1ELL/2022-01-21 | SICK O P E R A T I N G I N S T R U C T I O N S | microScan3 Pro I/O
221
Subject to change without notice

SICK microScan3 Pro I/O Specifications

General

Scanning angle	275°
Number of fields	128
Dimensions	102 mm x 152 mm x 106 mm
Number of safety outputs	2
Number of OSSD outputs	2
Scanning range	5.5 m
Protective field range	5.5 m
Resolution	30 mm
Number of monitoring cases	128
Response time	60 ms
Interfaces	Ethernet, USB
Operating temperature	+50 °C
Protection class	IP65
Supply voltage	24 V DC
Storage temperature	+70°C
Operating voltage	24 V DC (16.8 V DC ... 28.8 V DC)
Housing material	Plastic
Connection type	Male connector