Yamaha A3000 User Manual

Effect parameter list
343
Appendix
Appendix
33: Phaser2 (PHASER 2)
1 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance of the dry sound and effect sound
2 LFO Frequency 0.00Hz~39.7Hz Frequency of phase modulation
3 LFO Depth 0~127 Depth of phase modulation
4 Phase Shift Offset 0~127 Phase shift offset value
5 Feedback Level -63~+63 Level at which phaser output will be returned to the input (negative values invert the phase)
6 Stage 3, 4, 5, 6 Number of phaser shifter stages
7 LFOPhaseDifference -180deg~+180deg L/R phase difference in the modulation waveform (no difference at 0 deg (=64))
8 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
9 EQ Low Gain -12~+12dB Gain with which the EQ will boost/cut the low range
10 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
11 EQ High Gain -12~+12dB Gain with which the EQ will boost/cut the high range
34: Pitch1 (PITCH CHANGE 1)
1 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance of the dry sound and effect sound
2 Pitch -24~+24 Pitch change in semitone steps
3 Initial Delay 0.1~200ms Delay length
4 Fine1 -50Hz~+50Hz Fine pitch setting for first unit
5 Fine2 -50Hz~+50Hz Fine pitch setting for second unit
6 Feedback Level -63~+63 Amount of feedback
7 Pan1 L63~R63 Panning of first unit
8 Output Level1 0~127 Output level of first unit
9 Pan2 L63~R63 Panning of second unit
10 Output Level2 0~127 Output level of second unit
35: Pitch2 (PITCH CHANGE 2)
1 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance of the dry sound and effect sound
2 Pitch -24~+24 Pitch change in semitone steps
3 Initial Delay 0.1~200ms Delay length
4 Fine1 -50~+50cent Fine pitch setting for first unit
5 Fine2 -50~+50cent Fine pitch setting for second unit
6 Feedback Gain -63~+63 Amount of feedback
7 Pan1 L63~R63 Panning of first unit
8 Output Level1 0~127 Output level of first unit
9 Pan2 L63~R63 Panning of second unit
10 Output Level2 0~127 Output level of second unit
36: Detune (ENSEMBLE DETUNE)
1 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance of the dry sound and effect sound
2 Detune -50~+50cent Amount by which the pitch will be detuned
3 Initial Delay Lch 0~50.0ms Length of left channel delay
4 Initial Delay Rch 0~50.0ms Length of right channel delay
5 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
6 EQ Low Gain -12~+12dB Gain with which the EQ will boost/cut the low range
7 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
8 EQ High Gain -12~+12dB Gain with which the EQ will boost/cut the high range
37: Rotary (ROTARY SPEAKER)
1 LFO Frequency 0.00Hz~39.7Hz Rotation frequency of the speaker
2 LFO Depth 0~127 Depth of modulation produced by speaker rotation
3 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
4 EQ Low Gain -12~+12dB Gain with which the EQ will boost/cut the low range
5 EQ Mid Frequency 100Hz~10.0kHz Frequency at which the EQ will boost/cut the mid range
6 EQ Mid Gain -12~+12dB Gain with which the EQ will boost/cut the mid range
7 EQ Mid Width 1.0~12.0 Width of the mid range area which the EQ will boost/cut
8 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
9 EQ High Gain -12~+12dB Gain with which the EQ will boost/cut the high range
10 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance of the dry sound and effect sound

Yamaha A3000 Specifications

General

Sampling Rate	44.1kHz
MIDI	In/Out/Thru
Type	Sampler
Effects	Reverb, Chorus, Delay
Display	LCD
Storage	Floppy disk drive