Effect parameter list
344
Appendix
38: Ro2Way (2WAY ROTARY SPEAKER)
1 Rotor Speed 0.0Hz~39.7Hz Rotation frequency of the speaker
2 Drive Low 0~127 Depth of modulation produced by high-range speaker rotation
3 Drive High 0~127 Depth of modulation produced by low-range speaker rotation
4 Low/High Balance L63>H ~ L=H ~ L<H63 Volume balance between high-range speaker and low-range speaker
5 Crossover Frequency 100Hz~10.0kHz Crossover frequency between high-range speaker and low-range speaker
6 Mic L-R Angle 0deg~180deg L/R angle of mics which pick up the output
7 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
8 EQ Low Gain -12~+12dB Gain with which the EQ will boost/cut the low range
9 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
10 EQ High Gain -12~+12dB Gain with which the EQ will boost/cut the high range
39: Tremolo (TREMOLO)
1 LFO Frequency 0.00Hz~39.7Hz Modulation frequency
2 AM Depth 0~127 Amplitude modulation depth
3 PM Depth 0~127 Delay modulation depth
4 LFOPhaseDifference -180~+180deg L/R phase difference of the modulation waveform (no difference at 0 deg (=64))
5 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
6 EQ Low Gain -12~+12dB Gain with which the EQ will boost/cut the low range
7 EQ Mid Frequency 100Hz~10.0kHz Frequency at which the EQ will boost/cut the mid range
8 EQ Mid Gain -12~+12dB Gain with which the EQ will boost/cut the mid range
9 EQ Mid Width 1.0~12.0 Width of the mid range area which the EQ will boost/cut
10 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
11 EQ High Gain -12~+12dB Gain with which the EQ will boost/cut the high range
12 Input Mode mono, stereo Mono/stereo selection for the input
40: AutoPan (AUTO PAN)
1 LFO Frequency 0.00Hz~39.7Hz Auto pan frequency
2 L/R Depth 0~127 Left/right depth of panning
3 F/R Depth 0~127 Front/rear depth of panning
4 Pan Direction L<>R, L>>R, L<<R, Lturn, Rturn, L/R Auto pan type (L<->R is sine wave, L/R is square wave)
5 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
6 EQ Low Gain -12~+12dB Gain with which the EQ will boost/cut the low range
7 EQ Mid Frequency 100Hz~10.0kHz Frequency at which the EQ will boost/cut the mid range
8 EQ Mid Gain -12~+12dB Gain with which the EQ will boost/cut the mid range
9 EQ Mid Width 1.0~12.0 Width of the mid range area which the EQ will boost/cut
10 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
11 EQ High Gain -12~+12dB Gain with which the EQ will boost/cut the high range
41: Ambienc (AMBIENCE)
1 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance of the dry sound and effect sound
2 Delay Time 0~50.0ms Delay length
3 Wet Output Phase normal/invers Invert the phase of the effect sound between L/R
4 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
5 EQ Low Gain -12~+12dB Gain with which the EQ will boost/cut the low range
6 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
7 EQ High Gain -12~+12dB Gain with which the EQ will boost/cut the high range
42: 3Delay (DELAY L,C,R)
1 Dry/Wet Balance D63>W ~ D=W ~ D<W63 Balance of the dry sound and effect sound
2 Delay Time L 0.1~1480ms Length of left channel delay
3 Delay Time R 0.1~1480ms Length of right channel delay
4 Delay Time C 0.1~1480ms Length of center channel delay
5 Feedback Time 0.1~1480ms Length of feedback delay
6 Feedback Level -63~+63 Feedback amount
7 Delay Level C 0~127 Volume of center channel
8 Feedback High Damp 0.1~1.0 High range attenuation (lower values cause the high range to decay faster)
9 EQ Low Frequency 32Hz~2.0kHz Frequency at which the EQ will boost/cut the low range
10 EQ Low Gain -12~+12dB Gain with which the EQ will boost/cut the low range
11 EQ High Frequency 500Hz~16.0kHz Frequency at which the EQ will boost/cut the high range
12 EQ High Gain -12~+12dB Gain with which the EQ will boost/cut the high range
To Next Page
Loading...
Need help?
General
