DNS AS-410M User Manual

Structure of this Manual/ Table of Contents
AS-410M Auto Slide Preparation System 15
3-12-2 Routing of the carrier tape .............................................................................................................. 70
3-13 S ETTING THE INK RIBBON IN PLACE .......................................................................................... 71
3-14 S ETTING THE SUCTION FILTER OF PARAFFIN WASTE IN PLACE .................................................... 73
3-15 A DJUSTING THE TEMPERATURE CONTROLLERS ........................................................................ 74
3-16 C HECKING THE TEMPERATURE SETTING OF THE C OLLING U NIT ( BUILT IN THE M AIN U NIT ) .......... 76
3-16-1 Cooler control panel ....................................................................................................................... 76
3-16-2 Setting change of the cooler temperature ...................................................................................... 77
3-17 S TARTING AND EXITING THE A UTO S URFACE D ETECTION APPLICATION ...................................... 78
3-17-1 Start-up of the Auto Trimming (Auto Surface Detection) application .............................................. 79
3-17-2 Monitoring the Auto Trimming ......................................................................................................... 79
3-17-3 Exiting the Auto Trimming (Auto Surface Detection) application .................................................... 80
3-18 S TART - UP AND TERMINATION OF THE B LADE M ARK C HECK APPLICATION ................................... 81
3-18-1 Blade Mark Check application start-up ........................................................................................... 81
3-18-2 Termination of the Blade Mark Check application .......................................................................... 82
3-19 S TART - UP AND TERMINATION OF THE EXPANSION PACKAGE APPLICATION ................................... 83
3-19-1 Start-up and log-in of the expansion package application ............................................................. 83
3-19-2 Termination of the expansion package application ......................................................................... 85
3-20 S AFETY INTERLOCK ( DOOR LOCK ) ........................................................................................... 86
3-21 C OMPRESSOR ........................................................................................................................ 87
CHAPTER 4 - OPERATIONAL PROCEDURES - ......................................................................... 89
4-1 S ECTION SLIDE PREPARATION WORK FLOW ................................................................................ 92
4-2 O PERATIONAL PARAMETERS ...................................................................................................... 93
4-3 S ELECTING THE SECTIONING PARAMETERS FILE ......................................................................... 95
4-3-1 Selecting the sectioning parameters ................................................................................................ 95
4-3-2 Editing the sectioning parameters .................................................................................................... 96
4-3-3 Mount setting .................................................................................................................................... 97
4-3-4 Cut force setting ............................................................................................................................... 98
4-3-5 Saving .............................................................................................................................................100
4-4 S ECTION SLIDE PREPARATION ................................................................................................. 101
4-4-1 Preoperational checks ....................................................................................................................101
4-4-2 Selecting the Operation Mode ........................................................................................................104
4-5 P REOPERATIONAL SELF - DIAGNOSIS ......................................................................................... 115
4-5-1 “Start” prompt and warning messages ........................................................................................... 115
4-6 S TARTING SLIDE PREPARATION ................................................................................................ 117
4-7 S CREENS AND OPERATIONS DURING THE SLIDE PREPARATION .................................................. 118
4-7-1 Screens during slide preparation ................................................................................................... 118
4-7-2 Checks during the slide preparation ...............................................................................................123
4-8 E MERGENCY STOP .................................................................................................................. 127
4-9 E RROR - TRIGGERED SHUTDOWN .............................................................................................. 127
4-10 S HUTDOWN PROCEDURE ...................................................................................................... 128
4-10-1 Operation Completed screen .......................................................................................................129
4-10-2 Switching the Modes between the Normal Operating and the Overnight Operating ...................130
4-10-3 Saving and deleting operation log data ........................................................................................131
4-10-4 Checking the section slide quality and collecting section slides ..................................................133
4-11 M AINTENANCE M ODE ............................................................................................................ 134
4-12 R OUGH - CUT ( ROUGHING ) MODE ............................................................................................ 135
4-12-1 Roughing parameters ...................................................................................................................136
4-12-2 Outline of the operation and the preoperational setup .................................................................136
4-12-3 Outline of roughing operation .......................................................................................................137
4-12-4 Roughing condition settings .........................................................................................................138
4-12-5 Execution of roughing and operation buttons for use during roughing ........................................140
4-12-6 Screen during roughing ................................................................................................................140
4-12-7 Roughing completed screen .........................................................................................................141
4-13 I NITIALIZATION ...................................................................................................................... 142
4-13-1 Execution of initialization ..............................................................................................................142
4-14 S TAINING D ATA ..................................................................................................................... 143
4-14-1 Setting procedure .........................................................................................................................143
4-15 P RINT S ETTINGS ................................................................................................................... 145
4-16 E RROR L OG ......................................................................................................................... 151
4-16-1 Viewing the error log .....................................................................................................................151

DNS AS-410M Specifications

General

Brand	DNS
Model	AS-410M
Category	Industrial Equipment
Language	English