HellermannTyton TT4030 - Taking out of Operation; Taking the Device out of Operation; Putting the Device Back into Operation; 11 Disposal

Operating Instructions • Thermal Transfer Printer TT4030 • 06-2017 • 031-93478
Taking out of operation
22
10 Taking out of operation
DANGER
Danger of lethal electric shock!
There is a risk of lethal injury when touching live
components.
f Switch off the device before maintenance work.
f Pull the power plug out of the socket.
10.1 Taking the device out of operation
Proceed as follows:
1 Switch off the device using the main switch.
2 Pull the power plug of the device out of the socket.
3 Shut down the PC or notebook.
4 Disconnect the USB cable from the PC or notebook.
5 Disconnect the USB cable from the device.
6 Disconnect the power cable from the device.
; The device is stopped.
10.2 Putting the device back into operation
Proceed as follows:
1 Start the PC or notebook.
2 Connect the power cable to the device.
3 Connect the USB cable to the device.
4 Connect the USB cable of the device to the PC or
notebook.
5 Connect the power cable of the device to a power
socket.
6 Switch on the device using the main switch.
; The device is ready for operation.
11 Disposal
After termination of use, the purchaser or the operator
must properly dispose of the device including the
accessories.
The purchaser or the operator releases HellermannTyton
GmbH from the obligations according to paragraph
10passage2of the German Electrical and Electronic
Equipment Act (Return obligation of the manufacturer)
and from any associated third-party claims.
This device was manufactured according to the current
environmental protection standards. The materials can be
separated and recycled.
f Observe the national regulations for the disposal of
recyclable fractions, electronic parts and batteries.
f Do not dispose of the device with domestic waste.
f Bring the device to a local collection point or recycling
centre.
f If necessary, contact your local environmental oce.
12 Technical Specifications
TYPE Content Article No.
Thermal transfer printer
TT4030
1 556-04037
Printing method Thermal transfer printing
Print resolution 300 dpi
Print speed up to 300 mm/s
Print width up to 105.7 mm
Material
Labels or continuous material from roll
or fanfold labels
Energy supply 100 - 240 V
Rated input voltage 100 - 240 V AC ~ 50/60 Hz, PFC
Maximum rated input pow-
er
150 - 300 W
Input fuse max. 2 A
Interfaces
RS232 C, USB 2.0 Hi-Speed device for
PC connection, Ethernet 10/100
Base-T: LPD, IPv4, IPv 6, RawIP Printing,
DHCP, HTTP, FTP, SMTP, SNMP, TIME,
NTP, Zeroconf, SOAP-Web service,
1 x USB host for ext. control panel,
2 x USB host on the rear, keypad,
barcode scanner,
USB flash drive, USB bluetooth adapter,
WiFi, peripheral connection USB host
System requirements Windows XP
®
/Vista
®
/7
®
/8
®
Dimensions (W x H x D) 252mm x 288mm x 460mm
Weight 10 kg
Specification CE, FCC class A, CB, UL
Material
Label width 4 - 110 mm
Wide carrier material 9 - 114 mm
Continuous material width 9 - 114 mm
Continuous heat shrink
tubing width
4 - 85 mm
Label height without
backfeed above
4 mm
Label height up to 2000 mm
Supply roll outer diameter
up to
205 mm
Supply roll core diameter 38 - 100 mm
Colour ribbon
Roll diameter up to 80 mm
Core diameter 25.4 mm
Variable feed length up to 450 m
Width up to
(corresponding to the width
of the material)
114 mm
All dimensions in mm. We reserve the right to make technical changes without notice.