354
a: Sw
This parameter sets how the modulation source switches
between rotation and stop.
When “Sw” = Toggle, the speaker rotates or stops alternately
each time you press the pedal or operate the joystick.
Each time the value for the modulation source exceeds 64, the
speaker rotates or stops alternately.
When “Sw” = Moment, the speaker is rotating. It stops only
when you press the pedal or operate the joystick.
Rotation will occur when the value of the modulation source is
less than 64, and will stop when the value is 64 or greater.
b: Sw
This parameter sets how the rotation speed (slow and fast) is
switched via the modulation source.
When “Sw” = Toggle, the speed is switched between slow and
fast each time you press the pedal or operate the joystick.
Slow/fast will alternate each time the value of the modulation
source exceeds 64.
When “Sw” = Moment, the speed is usually slow. It becomes fast
only when you press the pedal or operate the joystick.
When a value for the modulation source is less than 64, “slow”
speed is selected, and when the value is 64 or higher, “fast” is
selected.
c: Manual Speed Ctrl
If you wish to control the speaker rotation speed manually, not
switching between Slow and Fast, select the modulation source in
the “Manual Speed Ctrl” field. If manual control is not necessary,
set this field to Off.
d: Horn Acceleration, e: Rotor Acceleration
On a real rotary speaker, the rotation speed is accelerated or
decelerated gradually after you switch the speed. The “Horn
Acceleration” parameter sets the speed at which the rotation is
accelerated or decelerated.
g: Mic Distance, g: Mic Spread
This is a simulation of stereo microphone settings.
ER/Delay
Early reflection and delay effects
041: Early Reflections
This effect is only the early reflection part of a reverberation
sound, and adds presence to the sound. You can select one of the
four decay curves.
a: Type
This parameter selects the decay curve for the early reflection.
h
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 330
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 330
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 330
–100...+100
Mic Spread
Microphone
Microphone
Mic Distance
Mic Distance
Rotary Speaker (Top View)
Rotary Speaker - Mic Placement
a
Type Sharp, Loose, Modulated, Reverse
Selects the decay curve for the early reflection
☞
b
ER Time [msec]
Sets the time length of early reflection
10...800msec
c
Pre Delay [msec] 0...200msec
Sets the time taken from the original sound to the first early reflection
d
EQ Trim 0...100
Sets the input level of EQ applied to the effect sound
e
Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 330
–15.0...+15.0dB
Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 330
–15.0...+15.0dB
f
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 330
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 330
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 330
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
EQ Trim
+
EQ Trim
Pre Delay
Early Reflections
LEQ HEQ
Sharp
Loose
Modulated
Early Reflections - Type
Reverse
Dry
Pre Delay
ER Time
To Next Page
Loading...
Need help?
General
