Korg PA1X - Page 357

353
Effects
Mod./P.Shift
Appendix
b: Pitch Shift [1/2tone], b: Src, b: Amt, c: Fine [cent], c: Amt
The amount of pitch shift will use the value of the “Pitch Shift”
plus the “Fine” value. The amount of modulation will use the c:
Amt value plus d: “Amt.”
Modulation Source is used both for “Pitch Shift” and “Fine.”
e: Feedback Position, f: Feedback
When “Feedback Position” is set to Pre, the pitch shifter output is
again input to the pitch shifter. Therefore, if you specify a higher
value for the Feedback parameter, the pitch will be raised (or
lowered) more and more each time feedback is repeated.
If “Feedback Position” is set to Post, the feedback signal will not
pass through the pitch shifter again. Even if you specify a higher
value for the Feedback parameter, the pitch-shifted sound will be
repeated at the same pitch.
039: Pitch Shift Mod.
(Pitch Shift Modulation)
This effect modulates the detuned pitch shift amount using an
LFO, adding a clear spread and width to the sound by panning
the effect sound and dry sound to the left and right. This is espe-
cially effective when the effect sound and dry sound output from
stereo speakers are mixed.
a: Pitch Shift [cent], e: Depth
These parameters set the amount of pitch shift and amount of
modulation by means of the LFO.
f: Pan, g: Wet/Dry
The Pan parameter pans the effect sound and dry sound to the
left and right. With L, the effect sound is panned left, and the dry
sound is panned right. With a Wet/Dry = Wet setting, the effect
and dry sound will be output in a proportion of 1:1.
040: Rotary Speaker
This effect simulates a rotary speaker, and obtains a more realis-
tic sound by simulating the rotor in the low range and the horn
in the high range separately. The effect also simulates the stereo
microphone settings.
a
Pitch Shift [cent]
Sets the pitch difference from the input signal
–100...+100cent
☞
b
LFO Waveform
Selects LFO Waveform
Triangle, Square
c
LFO Frequency [Hz] 0.02...20.00Hz
Sets the LFO speed
☞ Fx:009,
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using the
tempo and notes
☞ Fx:009,
BPM
Selects MIDI Clock and assigns tempo
MIDI, 40...240
☞ Fx:009
Base Note
                 
Selects the type of notes that specify the LFO speed ☞ Fx:009
Times x1...x16
Sets the number of notes that specify the LFO speed
☞ Fx:009
e
Depth –100...+100
Sets the LFO modulation depth for pitch shift amount
☞,
Src Off...Tempo
Selects the modulation source of the depth of modulation
Amt –100...+100
Sets the modulation amount of the depth of modulation
f
Pan L, 1:99...99:1, R
Sets the panning effect sound and dry sound separately
☞
g
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 330
☞,
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 330
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 330
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
LFO: Tri / Sqr
Pitch Shifter
Pan
+
a
Mode Switch
Switches between speaker rotation and stop
Rotate, Stop
Src Off...Tempo
Selects the modulation source that toggles between rotation and stop
Sw Toggle, Moment
Selects switching mode of the modulation source that toggles between rota-
tion and stop
☞
b
Speed Switch Slow, Fast
Switches the speaker rotation speed between slow and fast
Src Off...Tempo
Selects the modulation source that toggles between slow and fast
Sw Toggle, Moment
Selects switching mode of the modulation source that toggles between slow
and fast
☞
c
Manual Speed Ctrl (Manual Speed Control) Off...Tempo
Selects the modulation source in case the rotation speed is changed directly
☞,
d
Horn Acceleration 0...100
How quickly the horn rotation speed in the high range is switched
☞
Horn Ratio Stop, 0.50...2.00
Adjusts the (high-range side) horn rotation speed. Standard value is 1.00.
Selecting “Stop” will stop the rotation
e
Rotor Acceleration 0...100
Determines how quickly the rotor rotation speed in the low range is switched
☞
Rotor Ratio Stop, 0.50...2.00
Adjusts the (low-range side) rotor rotation speed. Standard value is 1.00.
Selecting “Stop” will stop the rotation
f
Horn/Rotor Balance Rotor, 1...99, Horn
Sets the level balance between the high-range horn and low-range rotor
g
Mic Distance 0...100
Sets the distance between the microphone and rotary speaker
☞
Mic Spread
Sets the angle of left and right microphones
0...100
☞
Pitch
Higher
Pitch Shift Mod - Pitch Shift / Depth
Lower
Original Pitch
Pitch Shift (+ value)
LFO Waveform=Triangle
Depth (+value)
LFO Waveform=Square
Depth (–value)
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
D
-mod
D
-mod
D
-mod
Mode Switch: Rotate/Stop
Speed Switch: Slow/Fast
Manual Speed Control
Speaker Simulation
Mic Distance
Mic Spread
Horn/Rotor
Balance
Horn
Rotary Speaker
Rotor
+