Nipro SURDIAL - Page 113

15-6
the ratio is 100% with exception that the speed is defined in the case of bolus infusion.
When the set ratio is 200%, it moves at a half speed compared with the case that the ratio is
100% with the exception.
(1) Press [F･5] SW to display maintenance mode 7 screen.
(2) Press [F･3] or [F･4] SW to indicate "20.MAINTENANCE MODE FREE".
［ＭＡＩＮＴＥ ７］
２０．ＭＡＩＮＴＥＮＡＮＣＥ ＭＯＤＥ ＦＲＥＥ ： ＯＦＦ
ＵＰ ＤＯＷＮ ＭＥＮＵ
Ｆ・１ Ｆ・２
Ｆ・３
Ｆ・４ Ｆ・５
(3) Press [F･1] SW to set to "ON".
［ＭＡＩＮＴＥ ７］
２０．ＭＡＩＮＴＥＮＡＮＣＥ ＭＯＤＥ ＦＲＥＥ ： ＯＮ
＋ － ＵＰ ＤＯＷＮ ＭＥＮＵ
Ｆ・１ Ｆ・２
Ｆ・３
Ｆ・４ Ｆ・５
(4) Instruction appears in [F･1] or [F･2] SW (＋/－). Check that setting is enabled by
blinking of items to be set.
(5) Press [F･3] or [F･4] SW to blink "1.SYRINGE RATE".
(6) Press [F･1] or [F･2] SW to change set value.
［ＭＡＩＮＴＥ ７］
１．ＳＹＲＩＮＧＥ ＲＡＴＥ ： １００
２．ＢＰ ＳＴＯＰ ＡＦＴＥＲ ＰＯＷＥＲ ＦＡＩＬ ： ＯＦＦ
＋ － ＵＰ ＤＯＷＮ ＭＥＮＵ
Ｆ・１ Ｆ・２
Ｆ・３
Ｆ・４ Ｆ・５
(7) Press [F･3] or [F･4] SW to indicate "20.MAINTENANCE MODE FREE".
(8) Press [F･1] SW to set to "OFF".
(9) Setting of syringe operation stop time
By the setting, automatic syringe operation stop is enabled at a set time before UF
completion and the stop is indicated by error message "E61 COMPLETION OF SYRINGE.P
INFUSION".
(1) Press [F･5] SW to display settingⅠscreen.
(2) Press [F･3] or [F･4] SW to blink "3.S.STP(min)".
(3) Press [F･1] or [F･2] SW to change set value.
(4) Check the changed set value.
［ＳＥＴＴＩＮＧ１］
１．ＴＥＭＰ （°Ｃ）：３７．０ ２．ＢＡＲ ＧＲＡＰＨ ：ＤＰ
３．Ｓ．ＳＴＰ（ｍｉｎ）： ０ ４．ＢＯＬＵＳ （ｍｌ）：０．０
＋ － ＜ ＞ ＤＩＳＰ．
Ｆ・１ Ｆ・２
Ｆ・３
Ｆ・４ Ｆ・５