Nipro SURDIAL - Setting of Dialysate Related Parameters; Setting of Dialysis Mode; Setting of Dialysate Concentration; Bicarbonate Dialysate

16-2
16.1. Setting of dialysate related parameters
1. Set dialysis mode.
2. Set dialysate concentration.
3. Set dialysate temperature.
16.1.1. Setting of dialysis mode
(1) Press [F･5] SW to display settingⅡscreen.
(2) Press [F･3] or [F･4] SW to blink "4.MODE".
(3) Press [F･1] or [F･2] SW to change setting.
(4) Check correct setting.
［ＳＥＴＴＩＮＧ２］
１．ＢＣ（Ｗ＋Ａ＋Ｂ） ：１４０ ２．ＢＣ（Ｗ＋Ａ） ：１１０
３．ＡＣ（Ｗ＋ＡＣ） ：１４０ ４．ＭＯＤＥ ：ＢＣ１
＋ － ＜ ＞ ＤＩＳＰ．
Ｆ・１ Ｆ・２
Ｆ・３
Ｆ・４ Ｆ・５
zBC1(BICARBONATE1) ：Execution of bicarbonate dialysis
zBC2(BICARBONATE2) ：Execution of bicarbonate dialysis
zAC(ACETATE) ：Execution of acetate dialysis
 ＷＡＲＮＩＮＧ
z Information concerning concentrate for each of BC1, BC2 and AC is found in
maintenance mode 5 screen. Set dialysis mode conforming to concentrate(s) intended to
be used.
z Both BC1 and BC2 are bicarbonate dialysis. Information not related to concentrate(s)
intended to be used may be shown in maintenance mode 5 screen. Take care of this.
16.1.2. Setting of dialysate concentration
16.1.2.1. Bicarbonate dialysate
(1) Press [F･5] SW to display settingⅡscreen.
(2) Press [F･3] or [F･4] SW to blink "1.BC(W+A+B)".
(3) Press [F･1] or [F･2] SW to change setting.
(4) Press [F･3] or [F･4] SW to blink "2.BC(W+A)".
(5) Press [F･1] or [F･2] SW to change setting.
(6) Check correct setting.
［ＳＥＴＴＩＮＧ２］
１．ＢＣ（Ｗ＋Ａ＋Ｂ） ：１４０ ２．ＢＣ（Ｗ＋Ａ） ：１１０
３．ＡＣ（Ｗ＋ＡＣ） ：１４０ ４．ＭＯＤＥ ：ＢＣ１
＋ － ＜ ＞ ＤＩＳＰ．
Ｆ・１ Ｆ・２
Ｆ・３
Ｆ・４ Ｆ・５
z1.BC(W+A+B) ：Setting of final concentration of bicarbonate dialysate by mmol/l unit
z2.BC(W+A) ：Setting of concentration of [water + A concentrate] in bicarbonate
dialysate by mmol/l unit