AudioCodes Media 800 MSBR - Page 917

Version 6.6 917 Mediant 800 MSBR
User's Manual 66. Configuration Parameters Reference
Parameter Description
Note: This parameter is applicable for Tel-to-IP and IP-to-Tel calls.
Web/EMS: Remove CLI
when Restricted
CLI: rmv-cli-when-restr
[RemoveCLIWhenRestr
icted]
Determines (for IP-to-Tel calls) whether the Calling Number and Calling
Name IEs are removed from the ISDN Setup message if the
presentation is set to Restricted.
 [0] No = (Default) IE's are not removed.
 [1] Yes = IE's are removed.
Web/EMS: Remove
Calling Name
CLI: rmv-calling-name
[RemoveCallingName]
Enables the device to remove the Calling Name from SIP-to-ISDN calls
for all trunks.
 [0] Disable = (Default) Does not remove Calling Name.
 [1] Enable = Removes Calling Name.
Note: Some PSTN switches / PBXs may not be configured to support
the receipt of the “Calling Name” information. These switches might
respond to an ISDN Setup message (including the Calling Name) with
an ISDN "REQUESTED_FAC_NOT_SUBSCRIBED" failure. This
parameter can be set to Enable (1) to remove the “Calling Name” from
SIP-to-ISDN calls and allow the call to proceed.
Web: Remove Calling
Name
EMS: Remove Calling
Name For Trunk Mode
[RemoveCallingNameF
orTrunk_x]
Enables the device to remove the Calling Name for SIP-to-ISDN calls,
per trunk.
 [-1] Use Global Parameter = (Default) Settings of the global
parameter RemoveCallingName are used.
 [0] Disable = Does not remove Calling Name.
 [1] Enable = Remove Calling Name.
Note: The x in the ini file parameter denotes the trunk number, where 0
is Trunk 1
Web/EMS: Progress
Indicator to ISDN
CLI: pi-to-isdn
[ProgressIndicator2ISD
N_x]
Determines the Progress Indicator (PI) to ISDN, per trunk.
 [-1] Not Configured = (Default) The PI in ISDN messages is set
according to the parameter PlayRBTone2Tel.
 [0] No PI = PI is not sent to ISDN.
 [1] PI = 1; [8] PI = 8: The PI value is sent to PSTN in
Q.931/Proceeding and Alerting messages. Typically, the PSTN/PBX
cuts through the audio channel without playing local ringback tone,
enabling the originating party to hear remote Call Progress Tones or
network announcements.
Note: The x in the ini file parameter denotes the trunk number, where 0
is Trunk 1.
Web: Set PI in Rx
Disconnect Message
EMS: Set PI For
Disconnect Msg
CLI: pi-in-rx-disc-msg
[PIForDisconnectMsg_
x]
Defines the device's behavior per trunk when a Disconnect message is
received from the ISDN before a Connect message is received.
 [-1] Not Configured = (Default) Sends a 183 SIP response according
to the received progress indicator (PI) in the ISDN Disconnect
message. If PI = 1 or 8, the device sends a 183 response, enabling
the PSTN to play a voice announcement to the IP side. If there isn't
a PI in the Disconnect message, the call is released.
 [0] No PI = Doesn't send a 183 response to IP. The call is released.
 [1] PI = 1; [8] PI = 8: Sends a 183 response to IP.
Note: The x in the ini file parameter denotes the trunk number, where 0
is Trunk 1.
EMS: Connect On
Progress Ind
[ConnectOnProgressIn
Enables the play of announcements from IP to PSTN without the need
to answer the Tel-to-IP call. It can be used with PSTN networks that
don't support the opening of a TDM channel before an ISDN Connect