Cisco ASR 9000 Series - Page 227

Fri May 18 10:32:46.332 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc3 UP Gi0/0/0/4.2 UP 1 UP
1111:2222::cdef
----------------------------------------------------------------------------------------
This example shows the output of the show l2vpn xconnect neighbor ipv6 command:
RP/0/RSP0/CPU0:router# show l2vpn xconnect neighbor ipv6 1111:2222::cdef
Fri May 18 10:32:46.332 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc3 UP Gi0/0/0/4.2 UP 1 UP
1111:2222::cdef
----------------------------------------------------------------------------------------
RP/0/RSP0/CPU0:router# show l2vpn xconnect neighbor ipv6 1111:2222::cdef detail
Fri May 18 10:33:57.813 EDT
Group g1, XC xc3, state is up; Interworking none
AC: GigabitEthernet0/0/0/4.2, state is up
Type VLAN; Num Ranges: 1
VLAN ranges: [2, 2]
MTU 1500; XC ID 0x2; interworking none
Statistics:
packets: received 0, sent 0
bytes: received 0, sent 0
drops: MTU exceeded 0, other 0
PW: neighbor 1111:2222::cdef, PW ID 1, state is up
PW class ts, XC ID 0x2
Encapsulation L2TPv3, protocol none
Source address 1111:2222::abcd
PW type Ethernet VLAN, control word disabled, interworking none
PW backup disable delay 0 sec
Sequencing not set
L2TP class not set, IPv6 source address 1111:2222::abcd
TOS 40 (reflect disabled), TTL 255, DF bit not set
Path MTU: disabled
L2TPv3 Local Remote
------------ ------------------------------ -----------------------------
Session 1 1
Cookie size 0 bytes 0 bytes
Cookie unassigned unassigned
------------ ------------------------------ -----------------------------
Create time: 18/05/2012 07:40:08 (04:12:49 ago)
Last time status changed: 18/05/2012 07:40:08 (04:12:49 ago)
Statistics:
packets: received 0, sent 0
bytes: received 0, sent 0
drops: out of sequence 0, other 0
This example shows the output of the show l2vpn xconnect state commands:
RP/0/RSP0/CPU0:router# show l2vpn xconnect state up
Fri May 18 10:36:45.913 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc3 UP Gi0/0/0/4.2 UP 1 UP
1111:2222::cdef
----------------------------------------------------------------------------------------
RP/0/RSP0/CPU0:router# show l2vpn xconnect state down
Fri May 18 10:37:25.113 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
Cisco ASR 9000 Series Aggregation Services Router VPN and Ethernet Services Command Reference, Release
6.1.x
213
Point to Point Layer 2 Services Commands
show l2vpn xconnect