EasyManuals Logo

Cisco Catalyst 3750-X Command Reference

Cisco Catalyst 3750-X
1244 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1028 background imageLoading...
Page #1028 background image
2-996
Catalyst 3750-X and 3560-X Switch Command Reference
OL-29704-01
Chapter 2 Catalyst 3750-X and 3560-X Switch Cisco IOS Commands
vtp (global configuration)
Follow these guidelines when setting VTP pruning:
VTP pruning removes information about each pruning-eligible VLAN from VTP updates if there
are no stations belonging to that VLAN.
If you enable pruning on the VTP server, it is enabled for the entire management domain for VLAN
IDs 1 to 1005.
Only VLANs in the pruning-eligible list can be pruned.
Pruning is supported with VTP Version 1 and Version 2.
Follow these guidelines when setting the VTP version:
Toggling the Version 2 (v2) mode state modifies parameters of certain default VLANs.
Each VTP switch automatically detects the capabilities of all the other VTP devices. To use
Version 2, all VTP switches in the network must support Version 2; otherwise, you must configure
them to operate in VTP Version 1 mode.
If all switches in a domain are VTP Version 2-capable, you need only to configure Version 2 on one
switch; the version number is then propagated to the other Version-2 capable switches in the VTP
domain.
If you are using VTP in a Token Ring environment, VTP Version 2 must be enabled.
If you are configuring a Token Ring bridge relay function (TrBRF) or Token Ring concentrator relay
function (TrCRF) VLAN media type, you must use Version 2.
If you are configuring a Token Ring or Token Ring-NET VLAN media type, you must use Version 1.
In VTP version 3, all database VTP information is propagated across the VTP domain, not only
VLAN database information.
Two VTP version 3 regions can only communicate over a VTP version 1 or VTP version 2 region in
transparent mode.
You cannot save password, pruning, and version configurations in the switch configuration file.
Examples This example shows how to rename the filename for VTP configuration storage to vtpfilename:
Switch(config)# vtp file vtpfilename
This example shows how to clear the device storage filename:
Switch(config)# no vtp file vtpconfig
Clearing device storage filename.
This example shows how to specify the name of the interface providing the VTP updater ID for this
device:
Switch(config)# vtp interface gigabitethernet
This example shows how to set the administrative domain for the switch:
Switch(config)# vtp domain OurDomainName
This example shows how to place the switch in VTP transparent mode:
Switch(config)# vtp mode transparent
This example shows how to configure the VTP domain password:
Switch(config)# vtp password ThisIsOurDomain’sPassword

Table of Contents

Other manuals for Cisco Catalyst 3750-X

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3750-X and is the answer not in the manual?

Cisco Catalyst 3750-X Specifications

General IconGeneral
Switching Capacity160 Gbps
Stacking Bandwidth64 Gbps
Max Stacking Units9
Layer SupportLayer 2 and Layer 3
Form FactorRack-mountable
DRAM256 MB
Flash Memory64 MB
ModelCisco Catalyst 3750-X Series
Ports24 or 48 10/100/1000 Ethernet ports
Uplink Interfaces4 SFP or 2 SFP+
FeaturesStackWise Plus, EnergyWise
ImageIP Base or IP Services
Operating Temperature0 to 40°C
Operating Humidity10 to 85% noncondensing

Related product manuals