Need help?Do you have a question about the NF BP4610 and is the answer not in the manual?
General| Efficiency | 85% |
|---|---|
| Input Voltage | 90-264VAC |
| Output Voltage | 12VDC |
| Safety Approvals | CE, UL, TUV, CB |
| Frequency | 47-63Hz |
| Protection | Over voltage, Short circuit |
Explains the meaning and usage of caution symbols in the manual for safety.
Covers essential safety practices like reading the manual, grounding, and checking power supply.
Details prohibitions like removing covers, modifying the product, and using specific symbols.
Provides a general description of the BP4610 bipolar DC power supply and its capabilities.
Lists the key features and functionalities of the BP4610, including its LCD, CV/CC modes, and signal sources.
Explains the main blocks and operational principles of the BP4610, illustrated with a block diagram.
Covers pre-operation checks, safety checks, and appearance/accessories verification before setup.
Specifies the required environmental conditions for safe and reliable operation, including temperature, humidity, and placement.
Details the critical procedures for grounding the unit and connecting the power supply for safety.
Explains how to connect various input/output terminals, including power, output pins, USB, and external control.
Describes the procedure for powering the BP4610 on and off, and performing an initial operation check.
Provides information regarding compliance with Japan's Radio Law for high-frequency application equipment.
Identifies and describes the main components of the operation panel, front panel, and rear panel.
Explains how to lift the operation panel to access internal adjustment knobs.
Details the LCD display layout, windows, status icons, and warning/error displays.
Covers fundamental operations like menu navigation, input methods, and shortcut keys.
Explains how to set operation modes, output on/off, voltage, current, AC parameters, and waveform.
Describes how to set output voltage and current limiters to protect the load and device.
Covers the advanced sequence programming, execution, control, and memory management features.
Explains how to save, recall, and manage settings using the device's memory functions.
Details how to control the BP4610 remotely via USB, including USB ID setting and mode switching.
Describes system settings like keylock, beep sound, LCD contrast, display color, and reset functions.
Explains the function for optimizing transient response characteristics for different load conditions.
Details how to use an external signal as a source or to add it to an internal signal.
Explains how to monitor output voltage and current using the dedicated monitor terminals.
Describes the capabilities for measuring output voltage and current, including DC and AC values.
Covers prerequisites for USB interface control, including driver installation and USB ID setup.
Lists and categorizes the program messages used for controlling the BP4610 via USB.
Provides detailed explanations of individual program messages for basic settings, limiters, sequences, and measurements.
Explains how status bits, event registers, and summaries are configured and used for monitoring.
Details how the BP4610 responds to specific interface messages for initialization and mode control.
Highlights important considerations and potential issues when programming arbitrary waveform data.
Lists and explains error messages, causes, and handling procedures for power-on and operational errors.
Details the protective functions like overload, overheat, and power failure, and their actions upon detection.
Provides a troubleshooting guide for common problems, their possible causes, and recommended handling.
Outlines the importance of maintenance for ensuring optimal performance and reliability.
Provides instructions for basic daily cleaning and care of the BP4610.
Gives guidelines for storing, repacking, and transporting the BP4610 safely.
Explains how to check the firmware version and system information displayed on the panel.
Details the procedure for cleaning the air filters to maintain proper airflow and cooling.
Explains the function and maintenance of the backup battery for memory preservation.
Describes checks to verify correct operation of the BP4610 under various conditions.
Outlines procedures for performing performance tests to ensure the BP4610 meets its specifications.
Lists the standard conditions under which the BP4610 specifications apply, including fixed and adjusted characteristics.
Details the output characteristics, including voltage/current ranges, frequency response, and rise/fall times.
Provides specifications for the output voltage and current limiters, including setting ranges and accuracy.
Lists the specifications for internal and external signal sources, including waveform, frequency, and amplitude.
Details the specifications for the voltage and current monitor outputs, including monitor ratio and frequency characteristics.
Lists the specifications for the measurement functions, including full scale, accuracy, and frequency bands.
Outlines the specifications for the sequence function, including number of steps, time, parameters, and control.
Provides general specifications for LCD display, beep, keylock, power-on settings, and reset functions.
Lists the specifications for the USB interface, including standard, USB ID range, and terminal details.
Provides the physical dimensions and weight of the BP4610 unit.
Shows graphical representations of output ranges based on various voltage limiter settings.
Lists the initial, shipping, at power-on, and after reset values for various settings.
To Next Page